Change all '$(...)' variable references into '${...}'

[platform/kernel/u-boot.git] / include / configs / inka4x0.h

diff --git a/include/configs/inka4x0.h b/include/configs/inka4x0.h
index 82a3842..c0cc4f1 100644 (file)
--- a/include/configs/inka4x0.h
+++ b/include/configs/inka4x0.h
@@ -112,14 +112,14 @@
 #define CONFIG_EXTRA_ENV_SETTINGS                                      \
        "netdev=eth0\0"                                                 \
        "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
-               "nfsroot=$(serverip):$(rootpath)\0"                     \
+               "nfsroot=${serverip}:${rootpath}\0"                     \
        "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
-       "addip=setenv bootargs $(bootargs) "                            \
-               "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)"      \
-               ":$(hostname):$(netdev):off panic=1\0"                  \
+       "addip=setenv bootargs ${bootargs} "                            \
+               "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
+               ":${hostname}:${netdev}:off panic=1\0"                  \
        "flash_nfs=run nfsargs addip;"                                  \
-               "bootm $(kernel_addr)\0"                                \
-       "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0"     \
+               "bootm ${kernel_addr}\0"                                \
+       "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"     \
        "rootpath=/opt/eldk/ppc_82xx\0"                                 \
        ""
 
@@ -197,8 +197,8 @@
 /*
  * GPIO configuration
  *
- * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1):
- *     Bit 0 (mask: 0x80000000): 1
+ * use CS1 as gpio_wkup_6 output
+ *     Bit 0 (mask: 0x80000000): 0
  * use ALT CAN position: Bits 2-3 (mask: 0x30000000):
  *     00 -> No Alternatives, I2C1 is used for onboard EEPROM
  *     01 -> CAN1 on I2C1, CAN2 on Tmr0/1 do not use on TQM5200 with onboard
@@ -206,14 +206,8 @@
  * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100
  * use PSC6_1 and PSC6_3 as GPIO: Bits 9:11 (mask: 0x07000000):
  *     011 -> PSC6 could not be used as UART or CODEC. IrDA still possible.
- * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST
- * tests.
  */
-#if defined (CONFIG_MINIFAP)
-#define CFG_GPS_PORT_CONFIG    0x93000004
-#else
-#define CFG_GPS_PORT_CONFIG    0x81001004
-#endif
+#define CFG_GPS_PORT_CONFIG    0x01001004
 
 /*
  * RTC configuration
@@ -311,22 +305,14 @@
 #define CFG_IDE_MAXDEVICE      2       /* max. 1 drive per IDE bus     */
 
 #define CFG_ATA_IDE0_OFFSET    0x0000
-
 #define CFG_ATA_BASE_ADDR      MPC5XXX_ATA
-
-/* Offset for data I/O                 */
-#define CFG_ATA_DATA_OFFSET    (0x0060)
-
-/* Offset for normal register accesses */
-#define CFG_ATA_REG_OFFSET     (CFG_ATA_DATA_OFFSET)
-
-/* Offset for alternate registers      */
-#define CFG_ATA_ALT_OFFSET     (0x005C)
-
-/* Interval between registers                                                */
-#define CFG_ATA_STRIDE          4
+#define CFG_ATA_DATA_OFFSET    0x0060  /* Offset for data I/O          */
+#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET) /* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET     0x005C  /* Offset for alternate registers */
+#define CFG_ATA_STRIDE          4      /* Interval between registers   */
 
 #define CONFIG_ATAPI            1
-#define CFG_BRIGHTNESS          0x20
+
+#define CFG_BRIGHTNESS          0xFF   /* LCD Default Brightness (255 = off) */
 
 #endif /* __CONFIG_H */