*
* Configuration settings for the LogicPD i.MX31 Litekit board.
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
/* High Level Configuration Options */
#define CONFIG_ARM1136 1 /* This is an arm1136 CPU core */
#define CONFIG_MX31 1 /* in a mx31 */
-#define CONFIG_MX31_HCLK_FREQ 26000000
#define CONFIG_MX31_CLK32 32000
#define CONFIG_DISPLAY_CPUINFO
* Hardware drivers
*/
-#define CONFIG_MXC_UART 1
-#define CONFIG_SYS_MX31_UART1 1
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART1_BASE
#define CONFIG_MXC_GPIO
#define CONFIG_HARD_SPI 1
#define CONFIG_DEFAULT_SPI_BUS 1
#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH)
-#define CONFIG_FSL_PMIC
+/* PMIC Controller */
+#define CONFIG_POWER
+#define CONFIG_POWER_SPI
+#define CONFIG_POWER_FSL
#define CONFIG_FSL_PMIC_BUS 1
#define CONFIG_FSL_PMIC_CS 0
#define CONFIG_FSL_PMIC_CLK 1000000
#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH)
-
-#define CONFIG_RTC_MC13783 1
+#define CONFIG_FSL_PMIC_BITLEN 32
+#define CONFIG_RTC_MC13XXX
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
/***********************************************************
* Command definition
"prg_uboot=tftpboot 0x80000000 u-boot-imx31_litekit.bin; protect off all; erase 0xa00d0000 0xa01effff; cp.b 0x80000000 0xa00d0000 $(filesize)\0"
-#define CONFIG_NET_MULTI
#define CONFIG_SMC911X 1
#define CONFIG_SMC911X_BASE (CS4_BASE + 0x00020000)
#define CONFIG_SMC911X_32_BIT 1
#define CONFIG_SYS_LOAD_ADDR 0 /* default load address */
-#define CONFIG_SYS_HZ 1000
-
#define CONFIG_CMDLINE_EDITING 1
/*-----------------------------------------------------------------------
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */
-
-/*-----------------------------------------------------------------------
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 1