#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */
#define CONFIG_HYMOD 1 /* ...on a Hymod board */
+#define CONFIG_CPM2 1 /* Has a CPM2 */
+
+#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
#define CONFIG_BOARD_POSTCLK_INIT /* have board_postclk_init() function */
* for FCC)
*
* if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
- * from CONFIG_COMMANDS to remove support for networking.
+ * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
*/
#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
#undef CONFIG_ETHER_NONE /* define if ether on something else */
#define CONFIG_ETHER_INDEX 1 /* which channel for ether */
+#define CONFIG_ETHER_LOOPBACK_TEST /* add ether external loopback test */
+
+#ifdef CONFIG_ETHER_ON_FCC
#if (CONFIG_ETHER_INDEX == 1)
# define CFG_CPMFCR_RAMTYPE 0
# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
+# define MDIO_PORT 0 /* Port A */
+# define MDIO_DATA_PINMASK 0x00040000 /* Pin 13 */
+# define MDIO_CLCK_PINMASK 0x00080000 /* Pin 12 */
+
#elif (CONFIG_ETHER_INDEX == 2)
/*
# define CFG_CPMFCR_RAMTYPE 0
# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
+# define MDIO_PORT 0 /* Port A */
+# define MDIO_DATA_PINMASK 0x00000040 /* Pin 25 */
+# define MDIO_CLCK_PINMASK 0x00000080 /* Pin 24 */
+
#elif (CONFIG_ETHER_INDEX == 3)
/*
# define CFG_CPMFCR_RAMTYPE 0
# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
+# define MDIO_PORT 0 /* Port A */
+# define MDIO_DATA_PINMASK 0x00000100 /* Pin 23 */
+# define MDIO_CLCK_PINMASK 0x00000200 /* Pin 22 */
+
#endif /* CONFIG_ETHER_INDEX */
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
+
+#define MDIO_ACTIVE (iop->pdir |= MDIO_DATA_PINMASK)
+#define MDIO_TRISTATE (iop->pdir &= ~MDIO_DATA_PINMASK)
+#define MDIO_READ ((iop->pdat & MDIO_DATA_PINMASK) != 0)
+
+#define MDIO(bit) if(bit) iop->pdat |= MDIO_DATA_PINMASK; \
+ else iop->pdat &= ~MDIO_DATA_PINMASK
+
+#define MDC(bit) if(bit) iop->pdat |= MDIO_CLCK_PINMASK; \
+ else iop->pdat &= ~MDIO_CLCK_PINMASK
+
+#define MIIDELAY udelay(1)
+
+#endif /* CONFIG_ETHER_ON_FCC */
+
/* other options */
#define CONFIG_HARD_I2C 1 /* To enable I2C hardware support */
+#define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */
/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
#ifdef DEBUG
#if defined(CONFIG_CONS_USE_EXTC)
#define CONFIG_BAUDRATE 115200
#else
-#define CONFIG_BAUDRATE 38400
+#define CONFIG_BAUDRATE 9600
#endif
/* default ip addresses - these will be overridden */
#define CONFIG_IPADDR 192.168.1.1 /* hymod "boot" address */
#define CONFIG_SERVERIP 192.168.1.254 /* hymod "server" address */
-#define CONFIG_COMMANDS (CFG_CMD_ALL & ~( \
- CFG_CMD_BEDBUG | \
- CFG_CMD_DOC | \
- CFG_CMD_ELF | \
- CFG_CMD_FDC | \
- CFG_CMD_FDOS | \
- CFG_CMD_HWFLOW | \
- CFG_CMD_IDE | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_MII | \
- CFG_CMD_PCMCIA | \
- CFG_CMD_PCI | \
- CFG_CMD_USB | \
- CFG_CMD_SCSI | \
- CFG_CMD_SPI | \
- CFG_CMD_VFD | \
- CFG_CMD_DTT ) )
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#define CONFIG_LAST_STAGE_INIT
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_CDP
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IMMAP
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_KGDB
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_PORTIO
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SAVES
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_SNTP
+
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_XIMG
#ifdef DEBUG
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#define CONFIG_BOOT_RETRY_TIME 30 /* retry autoboot after 30 secs */
+#define CONFIG_BOOT_RETRY_MIN 1 /* can go down to 1 second timeout */
+/* Be selective on what keys can delay or stop the autoboot process
+ * To stop use: " "
+ */
+#define CONFIG_AUTOBOOT_KEYED
+#define CONFIG_AUTOBOOT_PROMPT "Autobooting in %d seconds, " \
+ "press <SPACE> to stop\n", bootdelay
+#define CONFIG_AUTOBOOT_STOP_STR " "
+#undef CONFIG_AUTOBOOT_DELAY_STR
+#define DEBUG_BOOTKEYS 0
#endif
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */
#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */
#undef CONFIG_KGDB_NONE /* define if kgdb on something else */
# if defined(CONFIG_KGDB_USE_EXTC)
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */
# else
-#define CONFIG_KGDB_BAUDRATE 38400 /* speed to run kgdb serial port at */
+#define CONFIG_KGDB_BAUDRATE 9600 /* speed to run kgdb serial port at */
# endif
#endif
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_MEMTEST_START 0x00400000 /* memtest works on */
#define CFG_MEMTEST_END 0x03c00000 /* 4 ... 60 MB in DRAM */
+#define CFG_CLKS_IN_HZ 1 /* everything, incl board info, in Hz */
+
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
/* these are for the ST M24C02 2kbit serial i2c eeprom */
#define CFG_I2C_EEPROM_ADDR 0x50 /* base address */
#define CFG_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
+
+#define CFG_EEPROM_PAGE_WRITE_ENABLE 1 /* write eeprom in pages */
+#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* 16 byte write page size */
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+
+#define CFG_I2C_MULTI_EEPROMS 1 /* hymod has two eeproms */
+
#define CFG_I2C_RTC_ADDR 0x51 /* philips PCF8563 RTC address */
/*
+ * standard dtt sensor configuration - bottom bit will determine local or
+ * remote sensor of the ADM1021, the rest determines index into
+ * CFG_DTT_ADM1021 array below.
+ *
+ * On HYMOD board, the remote sensor should be connected to the MPC8260
+ * temperature diode thingy, but an errata said this didn't work and
+ * should be disabled - so it isn't connected.
+ */
+#if 0
+#define CONFIG_DTT_SENSORS { 0, 1 }
+#else
+#define CONFIG_DTT_SENSORS { 0 }
+#endif
+
+/*
+ * ADM1021 temp sensor configuration (see dtt/adm1021.c for details).
+ * there will be one entry in this array for each two (dummy) sensors in
+ * CONFIG_DTT_SENSORS.
+ *
+ * For HYMOD board:
+ * - only one ADM1021
+ * - i2c addr 0x2a (both ADD0 and ADD1 are N/C)
+ * - conversion rate 0x02 = 0.25 conversions/second
+ * - ALERT ouput disabled
+ * - local temp sensor enabled, min set to 0 deg, max set to 85 deg
+ * - remote temp sensor disabled (see comment for CONFIG_DTT_SENSORS above)
+ */
+#define CFG_DTT_ADM1021 { { 0x2a, 0x02, 0, 1, 0, 85, 0, } }
+
+/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
#define CFG_FLASH_ERASE_TOUT 120000 /* Flash Erase Timeout (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
-#define CFG_FLASH_TYPE FLASH_28F640J3A
-#define CFG_FLASH_ID (INTEL_ID_28F640J3A & 0xff)
-#define CFG_FLASH_NBLOCKS 64
-
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
-#define CFG_ENV_SECT_SIZE 0x40000 /* see README - env sect real size */
-#define CFG_ENV_ADDR (CFG_FLASH_BASE+CFG_MONITOR_LEN-CFG_ENV_SECT_SIZE)
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SIZE 0x40000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_SECT_SIZE 0x40000 /* see README - env sect real size */
+#define CONFIG_ENV_ADDR (CFG_FLASH_BASE+CFG_MONITOR_LEN-CONFIG_ENV_SECT_SIZE)
+#define CFG_USE_PPCENV /* Environment embedded in sect .ppcenv */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value*/
#endif
#define FPGA_MEZZ_ENABLE_PIN 3 /* PA3 */
/*
+ * FPGA Interrupt configuration
+ */
+#define FPGA_MAIN_IRQ SIU_INT_IRQ2
+
+/*
* Internal Definitions
*
* Boot Flags
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH*/
#define BOOTFLAG_WARM 0x02 /* Software reboot */
+/*
+ * JFFS2 partitions
+ *
+ */
+/* No command line, one static partition, whole device */
+#undef CONFIG_JFFS2_CMDLINE
+#define CONFIG_JFFS2_DEV "nor0"
+#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
+#define CONFIG_JFFS2_PART_OFFSET 0x00000000
+
+/* mtdparts command line support */
+/*
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT ""
+#define MTDPARTS_DEFAULT ""
+*/
+
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff