+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2014
- * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de
+ * Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
*
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 family */
-#define CONFIG_MPC83xx 1 /* MPC83xx family */
-#define CONFIG_MPC830x 1 /* MPC830x family */
-#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */
-#define CONFIG_HRCON 1 /* HRCON board specific */
-
-#define CONFIG_SYS_TEXT_BASE 0xFE000000
-
-#define CONFIG_BOARD_EARLY_INIT_R
-#define CONFIG_LAST_STAGE_INIT
-#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR
/*
- * System Clock Setup
- */
-#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
-#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
-
-/*
- * Hardware Reset Configuration Word
- * if CLKIN is 66.66MHz, then
- * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
- * We choose the A type silicon as default, so the core is 400Mhz.
- */
-#define CONFIG_SYS_HRCW_LOW (\
- HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
- HRCWL_DDR_TO_SCB_CLK_2X1 |\
- HRCWL_SVCOD_DIV_2 |\
- HRCWL_CSB_TO_CLKIN_4X1 |\
- HRCWL_CORE_TO_CSB_3X1)
-/*
- * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
- * in 8308's HRCWH according to the manual, but original Freescale's
- * code has them and I've expirienced some problems using the board
- * with BDI3000 attached when I've tried to set these bits to zero
- * (UART doesn't work after the 'reset run' command).
- */
-#define CONFIG_SYS_HRCW_HIGH (\
- HRCWH_PCI_HOST |\
- HRCWH_PCI1_ARBITER_ENABLE |\
- HRCWH_CORE_ENABLE |\
- HRCWH_FROM_0XFFF00100 |\
- HRCWH_BOOTSEQ_DISABLE |\
- HRCWH_SW_WATCHDOG_DISABLE |\
- HRCWH_ROM_LOC_LOCAL_16BIT |\
- HRCWH_RL_EXT_LEGACY |\
- HRCWH_TSEC1M_IN_RGMII |\
- HRCWH_TSEC2M_IN_RGMII |\
- HRCWH_BIG_ENDIAN)
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRH (\
- SICRH_ESDHC_A_SD |\
- SICRH_ESDHC_B_SD |\
- SICRH_ESDHC_C_SD |\
- SICRH_GPIO_A_GPIO |\
- SICRH_GPIO_B_GPIO |\
- SICRH_IEEE1588_A_GPIO |\
- SICRH_USB |\
- SICRH_GTM_GPIO |\
- SICRH_IEEE1588_B_GPIO |\
- SICRH_ETSEC2_GPIO |\
- SICRH_GPIOSEL_1 |\
- SICRH_TMROBI_V3P3 |\
- SICRH_TSOBI1_V2P5 |\
- SICRH_TSOBI2_V2P5) /* 0x0037f103 */
-#define CONFIG_SYS_SICRL (\
- SICRL_SPI_PF0 |\
- SICRL_UART_PF0 |\
- SICRL_IRQ_PF0 |\
- SICRL_I2C2_PF0 |\
- SICRL_ETSEC1_GTX_CLK125) /* 0x00000000 */
-
-/*
- * IMMR new address
- */
-#define CONFIG_SYS_IMMR 0xE0000000
-
-/*
* SERDES
*/
#define CONFIG_FSL_SERDES
#define CONFIG_FSL_SERDES1 0xe3000
/*
- * Arbiter Setup
- */
-#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
-#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */
-#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */
-
-/*
* DDR Setup
*/
-#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
| DDRCDR_PZ_LOZ \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
-#define CONFIG_SYS_LBC_LBCR 0x00040000
-
-/*
* FLASH on the Local Bus
*/
#if 1
-#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
-#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
#define CONFIG_FLASH_CFI_LEGACY
#define CONFIG_SYS_FLASH_LEGACY_512Kx16
#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is up to 8M */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
-
-/* Window base at flash base */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB)
-
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
- | BR_PS_16 /* 16 bit port */ \
- | BR_MS_GPCM /* MSEL = GPCM */ \
- | BR_V) /* valid */
-#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
- | OR_UPM_XAM \
- | OR_GPCM_CSNT \
- | OR_GPCM_ACS_DIV2 \
- | OR_GPCM_XACS \
- | OR_GPCM_SCY_15 \
- | OR_GPCM_TRLX_SET \
- | OR_GPCM_EHTR_SET)
+
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 135
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-/*
- * FPGA
- */
-#define CONFIG_SYS_FPGA0_BASE 0xE0600000
-#define CONFIG_SYS_FPGA0_SIZE 1 /* FPGA size is 1M */
-
-/* Window base at FPGA base */
-#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_FPGA0_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_1MB)
-
-#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FPGA0_BASE \
- | BR_PS_16 /* 16 bit port */ \
- | BR_MS_GPCM /* MSEL = GPCM */ \
- | BR_V) /* valid */
-#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \
- | OR_UPM_XAM \
- | OR_GPCM_CSNT \
- | OR_GPCM_ACS_DIV2 \
- | OR_GPCM_XACS \
- | OR_GPCM_SCY_15 \
- | OR_GPCM_TRLX_SET \
- | OR_GPCM_EHTR_SET)
-
-#define CONFIG_SYS_FPGA_BASE(k) CONFIG_SYS_FPGA0_BASE
#define CONFIG_SYS_FPGA_DONE(k) 0x0010
#define CONFIG_SYS_FPGA_COUNT 1
/*
* Serial Port
*/
-#define CONFIG_CONS_INDEX 2
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
/*
* Software (bit-bang) MII driver configuration
*/
-#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
#define CONFIG_BITBANGMII_MULTI
/*
/*
* TSEC
*/
-#define CONFIG_TSEC_ENET /* TSEC ethernet support */
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
/*
* TSEC ethernet configuration
*/
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_TSEC1
#define CONFIG_TSEC1_NAME "eTSEC0"
#define TSEC1_PHY_ADDR 1
/*
* Environment
*/
-#if 1
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
- CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
-#else
-#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
-#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* Command line configuration.
*/
-#define CONFIG_CMD_PCI
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/*
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
/*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT 0x000000000
-#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
- HID0_ENABLE_INSTRUCTION_CACHE | \
- HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
-#define CONFIG_SYS_HID2 HID2_HBE
-
-/*
- * MMU Setup
- */
-
-/* DDR: cache cacheable */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
- BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-
-/* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_RW | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
- BATU_VP)
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-
-/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
- BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
- BATL_CACHEINHIBIT | \
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-
-/* Stack in dcache: cacheable, no memory coherence */
-#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
-#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/*
* Environment Configuration
*/
#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
-#define CONFIG_HOSTNAME hrcon
+#define CONFIG_HOSTNAME "hrcon"
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_PREBOOT /* enable preboot variable */
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS1\0" \