/*
* Copyright 2010-2011 Calxeda, Inc.
*
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the Free
- * Software Foundation; either version 2 of the License, or (at your option)
- * any later version.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program. If not, see <http://www.gnu.org/licenses/>.
+ * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_L2_OFF
+#define CONFIG_SYS_DCACHE_OFF
+#define CONFIG_SYS_THUMB_BUILD
#define CONFIG_SYS_NO_FLASH
-#define CFG_HZ 1000
-#define CONFIG_SYS_HZ CFG_HZ
#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
#define CONFIG_FIT
+#define CONFIG_SUPPORT_RAW_INITRD
#define CONFIG_SYS_BOOTMAPSZ (16 << 20)
+#define CONFIG_SYS_TIMER_RATE (150000000/256)
+#define CONFIG_SYS_TIMER_COUNTER (0xFFF34000 + 0x4)
+#define CONFIG_SYS_TIMER_COUNTS_DOWN
+
/*
* Size of malloc() pool
*/
#define CONFIG_PL01x_PORTS { (void *)(0xFFF36000) }
#define CONFIG_CONS_INDEX 0
-#define CONFIG_BAUDRATE 38400
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTCOUNT_LIMIT
+#define CONFIG_SYS_BOOTCOUNT_SINGLEWORD
+#define CONFIG_SYS_BOOTCOUNT_LE /* Use little-endian accessors */
#define CONFIG_SYS_BOOTCOUNT_ADDR 0xfff3cf0c
#define CONFIG_MISC_INIT_R
+#define CONFIG_LIBATA
#define CONFIG_SCSI_AHCI
#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 5
CONFIG_SYS_SCSI_MAX_LUN)
#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
#define CONFIG_CALXEDA_XGMAC
#include <config_cmd_default.h>
#define CONFIG_CMD_BDI
+#define CONFIG_CMD_BOOTZ
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ELF
#define CONFIG_CMD_MEMORY
#define CONFIG_CMD_LOADS
#define CONFIG_CMD_SCSI
#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_FAT
#define CONFIG_CMD_PXE
#define CONFIG_MENU
#define CONFIG_BOOTDELAY 2
+#define CONFIG_BOOT_RETRY_TIME -1
+#define CONFIG_RESET_TO_RETRY
+#define CONFIG_AUTOBOOT_KEYED
+#define CONFIG_AUTOBOOT_PROMPT "Autobooting in %d seconds...\nPress <s> to stop or <d> to delay\n", bootdelay
+#define CONFIG_AUTOBOOT_KEYED_CTRLC
/*
* Miscellaneous configurable options
*/
#define CONFIG_CMDLINE_EDITING
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of cmd args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_PROMPT "Highbank #"
+#define CONFIG_SYS_HUSH_PARSER
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_LOAD_ADDR 0x800000
+#define CONFIG_SYS_64BIT_LBA
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "fdtaddr_r=0x600000\0" \
- "pxefile_addr_r=0x700000\0" \
- "kernel_addr_r=0x800000\0" \
- "ramdisk_addr_r=0x01000000\0" \
-
-/*-----------------------------------------------------------------------
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128*1024) /* regular stack */
-#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
-#endif
/*-----------------------------------------------------------------------
* Physical Memory Map
#define CONFIG_SYS_MEMTEST_START 0x100000
#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1_SIZE - 0x100000)
-/* Room required on the stack for the environment data */
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_IS_NOWHERE
+/* Environment data setup
+*/
+#define CONFIG_ENV_IS_IN_NVRAM
+#define CONFIG_SYS_NVRAM_BASE_ADDR 0xfff88000 /* NVRAM base address */
+#define CONFIG_SYS_NVRAM_SIZE 0x8000 /* NVRAM size */
+#define CONFIG_ENV_SIZE 0x2000 /* Size of Environ */
+#define CONFIG_ENV_ADDR CONFIG_SYS_NVRAM_BASE_ADDR
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_TEXT_BASE 0x00008000