#include <asm/arch/imx-regs.h>
#include <asm/mach-imx/gpio.h>
-#define CONFIG_BOARD_NAME "General Electric Bx50v3"
-
#include "mx6_common.h"
#include <linux/sizes.h>
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
-
/* SATA Configs */
#ifdef CONFIG_CMD_SATA
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_DWC_AHSATA_PORT_ID 0
#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
#define CONFIG_LBA48
#endif
-/* USB Configs */
-#ifdef CONFIG_USB
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
-#define CONFIG_MXC_USB_FLAGS 0
-
-#define CONFIG_USBD_HS
-#define CONFIG_USB_GADGET_MASS_STORAGE
-#endif
-
-/* Serial Flash */
-
-#define CONFIG_LOADADDR 0x12000000
-
#ifdef CONFIG_CMD_NFS
#define NETWORKBOOT \
"setnetworkboot=" \
"setenv netmask 255.255.255.0; setenv ethaddr ca:fe:de:ca:f0:11; " \
"setenv bootargs root=/dev/nfs nfsroot=${nfsserver}:/srv/nfs/,v3,tcp rw rootwait" \
"setenv bootargs $bootargs ip=${ipaddr}:${nfsserver}:${gatewayip}:${netmask}::eth0:off " \
- "setenv bootargs $bootargs cma=128M bootcause=POR ${videoargs} " \
+ "setenv bootargs $bootargs cma=128M bootcause=${bootcause} ${videoargs} " \
"setenv bootargs $bootargs systemd.mask=helix-network-defaults.service " \
"setenv bootargs $bootargs watchdog.handle_boot_enabled=1\0" \
"networkboot=" \
"run setnetworkboot; " \
"nfs ${loadaddr} /srv/nfs/fitImage; " \
- "bootm ${loadaddr}#conf@${confidx}\0" \
+ "bootm ${loadaddr}\0" \
-#define CONFIG_NETWORKBOOTCOMMAND \
+#define NETWORKBOOTCOMMAND \
"run networkboot; " \
#else
#define CONFIG_EXTRA_ENV_SETTINGS \
NETWORKBOOT \
- "bootcause=POR\0" \
"image=/boot/fitImage\0" \
"dev=mmc\0" \
"devnum=2\0" \
"swappartitions=" \
"setexpr partnum 3 - ${partnum}\0" \
"failbootcmd=" \
- "echo reached failbootcmd; " \
"cls; " \
"setcurs 5 4; " \
"lcdputs \"Monitor failed to start. " \
"Try again, or contact GE Service for support.\"; " \
- "bootcount reset; \0" \
+ "bootcount reset; " \
+ "while true; do sleep 1; done; \0" \
"altbootcmd=" \
"run doquiet; " \
"setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
"run hasfirstboot || setenv partnum 0; " \
"if test ${partnum} != 0; then " \
- "setenv bootcause REVERT; " \
"run swappartitions loadimage doboot; " \
"fi; " \
"run failbootcmd\0" \
"doboot=" \
"echo Booting from ${dev}:${devnum}:${partnum} ...; " \
"run setargs; " \
- "bootm ${loadaddr}#conf@${confidx}\0" \
+ "bootm ${loadaddr}\0" \
"tryboot=" \
"setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
"run loadimage || run swappartitions && run loadimage || " \
- "setenv partnum 0 && echo MISSING IMAGE;" \
+ "setenv partnum 0 && echo MISSING IMAGE;" \
"run doboot; " \
"run failbootcmd\0" \
-#define CONFIG_MMCBOOTCOMMAND \
- "if mmc dev ${devnum}; then " \
- "run doquiet; " \
- "run tryboot; " \
- "fi; " \
-
-#define CONFIG_USBBOOTCOMMAND \
- "echo Unsupported; " \
-
-#ifdef CONFIG_CMD_NFS
-#define CONFIG_BOOTCOMMAND CONFIG_NETWORKBOOTCOMMAND
-#elif CONFIG_CMD_USB
-#define CONFIG_BOOTCOMMAND CONFIG_USBBOOTCOMMAND
-#else
-#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND
-#endif
-
-
-/* Miscellaneous configurable options */
-
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
/* Physical Memory Map */
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_PCIE_IMX
-#define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12)
#define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(1, 5)
#endif /* __GE_BX50V3_CONFIG_H */