Merge tag 'xilinx-for-v2020.07-rc2' of https://gitlab.denx.de/u-boot/custodians/u...

[platform/kernel/u-boot.git] / include / configs / ge_bx50v3.h

diff --git a/include/configs/ge_bx50v3.h b/include/configs/ge_bx50v3.h
index b8b1ec7..3bf0cd5 100644 (file)
--- a/include/configs/ge_bx50v3.h
+++ b/include/configs/ge_bx50v3.h
@@ -16,9 +16,6 @@
 
 #define CONFIG_BOARD_NAME      "General Electric Bx50v3"
 
-#define CONFIG_MXC_UART_BASE   UART3_BASE
-#define CONSOLE_DEV    "ttymxc2"
-
 #include "mx6_common.h"
 #include <linux/sizes.h>
 
@@ -28,8 +25,6 @@
 #define CONFIG_REVISION_TAG
 #define CONFIG_SYS_MALLOC_LEN          (10 * SZ_1M)
 
-#define CONFIG_MXC_UART
-
 /* SATA Configs */
 #ifdef CONFIG_CMD_SATA
 #define CONFIG_SYS_SATA_MAX_DEVICE     1
@@ -64,7 +59,7 @@
                 "setenv netmask 255.255.255.0; setenv ethaddr ca:fe:de:ca:f0:11; " \
                 "setenv bootargs root=/dev/nfs nfsroot=${nfsserver}:/srv/nfs/,v3,tcp rw rootwait" \
                 "setenv bootargs $bootargs ip=${ipaddr}:${nfsserver}:${gatewayip}:${netmask}::eth0:off " \
-                "setenv bootargs $bootargs cma=128M bootcause=POR console=${console} ${videoargs} " \
+                "setenv bootargs $bootargs cma=128M bootcause=POR ${videoargs} " \
                 "setenv bootargs $bootargs systemd.mask=helix-network-defaults.service " \
                 "setenv bootargs $bootargs watchdog.handle_boot_enabled=1\0" \
         "networkboot=" \
@@ -84,34 +79,29 @@
        NETWORKBOOT \
        "bootcause=POR\0" \
        "image=/boot/fitImage\0" \
-       "fdt_high=0xffffffff\0" \
        "dev=mmc\0" \
        "devnum=2\0" \
        "rootdev=mmcblk0p\0" \
        "quiet=quiet loglevel=0\0" \
-       "console=" CONSOLE_DEV "\0" \
        "setargs=setenv bootargs root=/dev/${rootdev}${partnum} " \
                "ro rootwait cma=128M " \
                "bootcause=${bootcause} " \
-               "${quiet} console=${console} " \
+               "${quiet} " \
                "${videoargs}" "\0" \
        "doquiet=" \
                "if ext2load ${dev} ${devnum}:5 0x7000A000 /boot/console; " \
                        "then setenv quiet; fi\0" \
        "hasfirstboot=" \
-               "ext2load ${dev} ${devnum}:${partnum} 0x7000A000 " \
-               "/boot/bootcause/firstboot\0" \
+               "test -e ${dev} ${devnum}:${partnum} /boot/bootcause/firstboot\0" \
        "swappartitions=" \
                "setexpr partnum 3 - ${partnum}\0" \
        "failbootcmd=" \
                "echo reached failbootcmd; " \
-               "bx50_backlight_enable; " \
+               "cls; " \
                "setcurs 5 4; " \
                "lcdputs \"Monitor failed to start. " \
                "Try again, or contact GE Service for support.\"; " \
-               "mw.b 0x7000A000 0xbc; " \
-               "mw.b 0x7000A001 0x00; " \
-               "ext4write ${dev} ${devnum}:5 0x7000A000 /boot/failures 2\0" \
+               "bootcount reset; \0" \
        "altbootcmd=" \
                "run doquiet; " \
                "setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
@@ -163,6 +153,8 @@
 /* Physical Memory Map */
 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 
+#define CONFIG_SYS_BOOTMAPSZ (256 << 20)     /* 256M */
+
 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE