#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */
#define CONFIG_SYS_MPC5XXX_CLKIN 33333333 /* ... running at 33.333333MHz */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Valid values for CONFIG_SYS_TEXT_BASE are:
+ * 0xFFF00000 boot high (standard configuration)
+ * 0xFE000000 boot low
+ * 0x00100000 boot from RAM (for testing only) does not work
+ */
+#ifdef CONFIG_galaxy5200_LOWBOOT
+#define CONFIG_SYS_TEXT_BASE 0xFE000000
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xFFF00000 /* Standard: boot high */
+#endif
/*
* Serial console configuration
#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */
-#if (TEXT_BASE == 0xFE000000) /* Boot low */
+#if (CONFIG_SYS_TEXT_BASE == 0xFE000000) /* Boot low */
#define CONFIG_SYS_LOWBOOT 1
#endif
/* RAMBOOT will be defined automatically in memory section */
/*
* Autobooting
*/
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+#define CONFIG_BOOTDELAY 10 /* autoboot after 10 seconds */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* allow stopping of boot process */
/* even with bootdelay=0 */
-#undef CONFIG_BOOTARGS
+#define CONFIG_BOOT_RETRY_TIME 120 /* Reset if no command is entered */
+#define CONFIG_RESET_TO_RETRY
#define CONFIG_PREBOOT "echo;" \
"echo Welcome to U-Boot;"\
"echo"
+#define CONFIG_BOOTCOMMAND "go ff300004 0; go ff300004 2 2;" \
+ "bootm ff040000 ff900000 fffc0000"
+#define CONFIG_BOOTARGS "console=ttyPSC0,115200"
+#define CONFIG_EXTRA_ENV_SETTINGS "epson=yes\0"
+
/*
* IPB Bus clocking configuration.
*/
#define CONFIG_SYS_FLASH_BASE 0xfe000000
/*
- * The flash size is autoconfigured, but cpu/mpc5xxx/cpu_init.c needs this
+ * The flash size is autoconfigured, but arch/powerpc/cpu/mpc5xxx/cpu_init.c needs this
* variable defined
*/
#define CONFIG_SYS_FLASH_SIZE 0x02000000
#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
/* End of used area in SPRAM */
-#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE
-
-/* Size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_SIZE 128
+#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \
- CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
# define CONFIG_SYS_RAMBOOT 1
#endif
/* Chip Select configuration for NAND flash */
#define CONFIG_SYS_CS1_START 0x20000000
#define CONFIG_SYS_CS1_SIZE 0x90000
-#define CONFIG_SYS_CS1_CFG 0x0002d900
+#define CONFIG_SYS_CS1_CFG 0x00025b00
/* Chip Select configuration for Epson S1D13513 */
#define CONFIG_SYS_CS3_START 0x10000000