+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2011, Stefano Babic <sbabic@denx.de>
*
* Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
*
* Configuration for the flea3 board.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
/* High Level Configuration Options */
#define CONFIG_MX35
-#define CONFIG_SYS_DCACHE_OFF
-
#define CONFIG_MACH_TYPE MACH_TYPE_FLEA3
/* Set TEXT at the beginning of the NOR flash */
-#define CONFIG_SYS_TEXT_BASE 0xA0000000
/* This is required to setup the ESDC controller */
/*
* Hardware drivers
*/
-#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_LEGACY
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
#define CONFIG_SYS_SPD_BUS_NUM 2 /* I2C3 */
#define CONFIG_SYS_MXC_I2C3_SLAVE 0xfe
-#define CONFIG_MXC_SPI
-#define CONFIG_MXC_GPIO
/*
* UART (console)
*/
-#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE UART3_BASE
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_CONS_INDEX 1
-
/*
* Command definition
*/
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_DNS
#define CONFIG_NET_RETRY_COUNT 100
*/
#define CONFIG_FEC_MXC
#define IMX_FEC_BASE FEC_BASE_ADDR
-#define CONFIG_PHYLIB
-#define CONFIG_PHY_MICREL
#define CONFIG_FEC_MXC_PHYADDR 0x1
-#define CONFIG_MII
-
#define CONFIG_ARP_TIMEOUT 200UL
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x10000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
/*
* Physical Memory Map
*/
-#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 CSD0_BASE_ADDR
#define PHYS_SDRAM_1_SIZE (128 * 1024 * 1024)
/*
* MTD Command for mtdparts
*/
-#define CONFIG_MTD_DEVICE
-#define CONFIG_FLASH_CFI_MTD
-#define CONFIG_MTD_PARTITIONS
-#define MTDIDS_DEFAULT "nand0=mxc_nand,nor0=physmap-flash.0"
-#define MTDPARTS_DEFAULT "mtdparts=mxc_nand:50m(root1)," \
- "32m(rootfb)," \
- "64m(pcache)," \
- "64m(app1)," \
- "10m(app2),-(spool);" \
- "physmap-flash.0:512k(u-boot),64k(env1)," \
- "64k(env2),3776k(kernel1),3776k(kernel2)"
/*
* FLASH and environment organization
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
-#define CONFIG_ENV_SECT_SIZE (64 * 1024)
-#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-
/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
-
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
- CONFIG_SYS_MONITOR_LEN)
/*
* CFI FLASH driver setup
*/
-#define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */
-#define CONFIG_FLASH_CFI_DRIVER
/* A non-standard buffered write algorithm */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* faster */
-#define CONFIG_SYS_FLASH_PROTECTION /* Use hardware sector protection */
/*
* NAND FLASH driver setup
*/
-#define CONFIG_NAND_MXC
#define CONFIG_MXC_NAND_REGS_BASE (NFC_BASE_ADDR)
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE (NFC_BASE_ADDR)
* to update uboot and load kernel
*/
-#define CONFIG_HOSTNAME flea3
+#define CONFIG_HOSTNAME "flea3"
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"addmisc=setenv bootargs ${bootargs} ${misc}\0" \
"loadaddr=80800000\0" \
"kernel_addr_r=80800000\0" \
- "hostname=" __stringify(CONFIG_HOSTNAME) "\0" \
- "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0" \
- "ramdisk_file=" __stringify(CONFIG_HOSTNAME) "/uRamdisk\0" \
+ "hostname=" CONFIG_HOSTNAME "\0" \
+ "bootfile=" CONFIG_HOSTNAME "/uImage\0" \
+ "ramdisk_file=" CONFIG_HOSTNAME "/uRamdisk\0" \
"flash_self=run ramargs addip addtty addmtd addmisc;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
"run ramargs addip addtty addmtd addmisc;" \
"bootm ${kernel_addr_r} ${ramdisk_addr_r};" \
"else echo Images not loades;fi\0" \
- "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.bin\0" \
+ "u-boot=" CONFIG_HOSTNAME "/u-boot.bin\0" \
"load=tftp ${loadaddr} ${u-boot}\0" \
"uboot_addr=" __stringify(CONFIG_SYS_MONITOR_BASE) "\0" \
"update=protect off ${uboot_addr} +80000;" \
projects / platform / kernel / u-boot.git / blobdiff