Convert CONFIG_SPL_STACK to Kconfig

[platform/kernel/u-boot.git] / include / configs / edminiv2.h

diff --git a/include/configs/edminiv2.h b/include/configs/edminiv2.h
index 686d122..2bc9c99 100644 (file)
--- a/include/configs/edminiv2.h
+++ b/include/configs/edminiv2.h
@@ -15,10 +15,7 @@
  * SPL
  */
 
-#define CONFIG_SPL_MAX_SIZE            0x0000fff0
-#define CONFIG_SPL_STACK               0x00020000
 #define CONFIG_SPL_BSS_START_ADDR      0x00020000
-#define CONFIG_SPL_BSS_MAX_SIZE                0x0001ffff
 #define CONFIG_SYS_SPL_MALLOC_START    0x00040000
 #define CONFIG_SYS_SPL_MALLOC_SIZE     0x0001ffff
 #define CONFIG_SYS_UBOOT_BASE          0xfff90000
@@ -28,9 +25,6 @@
  * High Level Configuration Options (easy to change)
  */
 
-#define CONFIG_FEROCEON                1       /* CPU Core subversion */
-#define CONFIG_88F5182         1       /* SOC Name */
-
 #include <asm/arch/orion5x.h>
 /*
  * CLKs configurations
@@ -88,24 +82,12 @@
  * FLASH configuration
  */
 
-#define CONFIG_SYS_MAX_FLASH_BANKS     1  /* max num of flash banks       */
 #define CONFIG_SYS_MAX_FLASH_SECT      11 /* max num of sects on one chip */
 #define CONFIG_SYS_FLASH_BASE          0xfff80000
 
 /* auto boot */
 
 /*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_CMDLINE_TAG     1       /* enable passing of ATAGs  */
-#define CONFIG_INITRD_TAG      1       /* enable INITRD tag */
-#define CONFIG_SETUP_MEMORY_TAGS 1     /* enable memory tag */
-
-#define        CONFIG_SYS_CBSIZE       1024    /* Console I/O Buff Size */
-
-/*
  * Network
  */
 
@@ -113,8 +95,6 @@
 #define CONFIG_MVGBE_PORTS     {1}             /* enable port 0 only */
 #define CONFIG_SKIP_LOCAL_MAC_RANDOMIZATION    /* don't randomize MAC */
 #define CONFIG_PHY_BASE_ADR    0x8
-#define CONFIG_RESET_PHY_R     /* use reset_phy() to init mv8831116 PHY */
-#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN        /* detect link using phy */
 #endif
 
 /*
@@ -122,23 +102,13 @@
  */
 #ifdef CONFIG_IDE
 #define __io
-/* Needs byte-swapping for ATA data register */
-#define CONFIG_IDE_SWAP_IO
 /* Data, registers and alternate blocks are at the same offset */
-#define CONFIG_SYS_ATA_DATA_OFFSET     (0x0100)
-#define CONFIG_SYS_ATA_REG_OFFSET      (0x0100)
-#define CONFIG_SYS_ATA_ALT_OFFSET      (0x0100)
 /* Each 8-bit ATA register is aligned to a 4-bytes address */
-#define CONFIG_SYS_ATA_STRIDE          4
 /* Controller supports 48-bits LBA addressing */
 #define CONFIG_LBA48
 /* A single bus, a single device */
-#define CONFIG_SYS_IDE_MAXBUS          1
-#define CONFIG_SYS_IDE_MAXDEVICE       1
 /* ATA registers base is at SATA controller base */
-#define CONFIG_SYS_ATA_BASE_ADDR       ORION5X_SATA_BASE
 /* ATA bus 0 is orion5x port 1 on ED Mini V2 */
-#define CONFIG_SYS_ATA_IDE0_OFFSET     ORION5X_SATA_PORT1_OFFSET
 /* end of IDE defines */
 #endif /* CMD_IDE */
 
@@ -154,33 +124,17 @@
  */
 #ifdef CONFIG_CMD_I2C
 #define CONFIG_I2C_MVTWSI_BASE0                ORION5X_TWSI_BASE
-#define CONFIG_SYS_I2C_SLAVE           0x0
-#define CONFIG_SYS_I2C_SPEED           100000
 #endif
 
 /*
  *  Environment variables configurations
  */
 
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN  (1024 * 256) /* 256kB for malloc() */
-
-/*
- * Other required minimal configurations
- */
-
-#define CONFIG_SYS_LOAD_ADDR           0x00800000
-#define CONFIG_SYS_RESET_ADDRESS       0xffff0000
-
 /* Enable command line editing */
 
 /* provide extensive help */
 
 /* additions for new relocation code, must be added to all boards */
 #define CONFIG_SYS_SDRAM_BASE          0
-#define CONFIG_SYS_INIT_SP_ADDR        \
-       (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
 
 #endif /* _CONFIG_EDMINIV2_H */