/*
- * Copyright (C) 2010 Albert ARIBAUD <albert.aribaud@free.fr>
+ * Copyright (C) 2010 Albert ARIBAUD <albert.u.boot@aribaud.net>
*
* Based on original Kirkwood support which is
* (C) Copyright 2009
#define ORION5X_MPP0_7 0x00000003
#define ORION5X_MPP8_15 0x55550000
-#define ORION5X_MPP16_23 0x00000000
+#define ORION5X_MPP16_23 0x00005555
/*
* Board-specific values for Orion5x GPIO low level init:
* Commands configuration - using default command set for now
*/
#include <config_cmd_default.h>
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_I2C
+
+/*
+ * Network
+ */
+
+#ifdef CONFIG_CMD_NET
+#define CONFIG_MVGBE /* Enable Marvell GbE Driver */
+#define CONFIG_MVGBE_PORTS {1} /* enable port 0 only */
+#define CONFIG_SKIP_LOCAL_MAC_RANDOMIZATION /* don't randomize MAC */
+#define CONFIG_PHY_BASE_ADR 0x8
+#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* specify more that one ports available */
+#define CONFIG_MII /* expose smi ove miiphy interface */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+#endif
+
/*
- * Disabling some default commands for staggered bring-up
+ * IDE
*/
-#undef CONFIG_CMD_BOOTD /* no bootd since no net */
-#undef CONFIG_CMD_NET /* no net since no eth */
-#undef CONFIG_CMD_NFS /* no NFS since no net */
+#ifdef CONFIG_CMD_IDE
+#define __io
+#define CONFIG_IDE_PREINIT
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+/* ED Mini V has an IDE-compatible SATA connector for port 1 */
+#define CONFIG_MVSATA_IDE
+#define CONFIG_MVSATA_IDE_USE_PORT1
+/* Needs byte-swapping for ATA data register */
+#define CONFIG_IDE_SWAP_IO
+/* Data, registers and alternate blocks are at the same offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100)
+#define CONFIG_SYS_ATA_REG_OFFSET (0x0100)
+#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100)
+/* Each 8-bit ATA register is aligned to a 4-bytes address */
+#define CONFIG_SYS_ATA_STRIDE 4
+/* Controller supports 48-bits LBA addressing */
+#define CONFIG_LBA48
+/* A single bus, a single device */
+#define CONFIG_SYS_IDE_MAXBUS 1
+#define CONFIG_SYS_IDE_MAXDEVICE 1
+/* ATA registers base is at SATA controller base */
+#define CONFIG_SYS_ATA_BASE_ADDR ORION5X_SATA_BASE
+/* ATA bus 0 is orion5x port 1 on ED Mini V2 */
+#define CONFIG_SYS_ATA_IDE0_OFFSET ORION5X_SATA_PORT1_OFFSET
+/* end of IDE defines */
+#endif /* CMD_IDE */
+
+/*
+ * I2C related stuff
+ */
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_I2C_MVTWSI
+#define CONFIG_I2C_MVTWSI_BASE ORION5X_TWSI_BASE
+#define CONFIG_SYS_I2C_SLAVE 0x0
+#define CONFIG_SYS_I2C_SPEED 100000
+#endif
/*
* Environment variables configurations
*/
#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */
/* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_SIZE 128
/*
* Other required minimal configurations
#define CONFIG_SYS_RESET_ADDRESS 0xffff0000
#define CONFIG_SYS_MAXARGS 16
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_SDRAM_BASE 0
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
#endif /* _CONFIG_EDMINIV2_H */