* for DDR ECC byte filling in the SPL before loading the main
* U-Boot into it.
*/
-#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MVTWSI
#define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE
-#define CONFIG_SYS_I2C_SLAVE 0x0
-#define CONFIG_SYS_I2C_SPEED 100000
-
-/* Environment in SPI NOR flash */
-
-#define CONFIG_SYS_NETA_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII
-
-/* PCIe support */
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_PCI_SCAN_SHOW
-#endif
-
-/* USB/EHCI/XHCI configuration */
-
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
-
-/* FIXME: broken XHCI support
- * Below defines should enable support for the two rear USB3 ports. Sadly, this
- * does not work because:
- * - xhci-pci seems to not support DM_USB, so with that enabled it is not
- * found.
- * - USB init fails, controller does not respond in time */
-
-#if !defined(CONFIG_USB_XHCI_HCD)
-#define CONFIG_EHCI_IS_TDI
-#endif
-
-/* why is this only defined in mv-common.h if CONFIG_DM is undefined? */
/*
* mv-common.h should be defined after CMD configs since it used them
/* SPL */
/* Defines for SPL */
-#define CONFIG_SPL_MAX_SIZE ((128 << 10) - 0x4030)
-
-#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + (128 << 10))
-#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MALLOC_SIMPLE
-#endif
-
-#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10))
-#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
+/* Default Environment */
-#if defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI)
-/* SPL related SPI defines */
-#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS
-#endif
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "initrd_high=0xffffffff\0" \
+ "ramdisk_addr_r=0x8000000\0" \
+ "usb0Mode=host\0usb1Mode=host\0usb2Mode=device\0" \
+ "ethmtu=1500\0eth1mtu=1500\0" \
+ "update_uboot=sf probe; dhcp; " \
+ "mw.b ${loadaddr} 0x0 0xd0000; " \
+ "tftpboot ${loadaddr} u-boot-spl.kwb; " \
+ "sf update ${loadaddr} 0x0 0xd0000\0"
-/* DS414 bus width is 32bits */
-#define CONFIG_DDR_32BIT
-/* Default Environment */
-#define CONFIG_BOOTCOMMAND "sf read ${loadaddr} 0xd0000 0x700000; bootm"
-#define CONFIG_LOADADDR 0x80000
+/* increase autoneg timeout, my NIC sucks */
+#define PHY_ANEG_TIMEOUT 16000
#endif /* _CONFIG_SYNOLOGY_DS414_H */