Convert CONFIG_SPL_STACK to Kconfig

[platform/kernel/u-boot.git] / include / configs / ds414.h

diff --git a/include/configs/ds414.h b/include/configs/ds414.h
index b179b99..16d59ed 100644 (file)
--- a/include/configs/ds414.h
+++ b/include/configs/ds414.h
@@ -15,45 +15,15 @@
  * for DDR ECC byte filling in the SPL before loading the main
  * U-Boot into it.
  */
-#define CONFIG_SYS_TCLK                250000000       /* 250MHz */
-
-/*
- * Commands configuration
- */
 
 /* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MVTWSI
 #define CONFIG_I2C_MVTWSI_BASE0                MVEBU_TWSI_BASE
-#define CONFIG_SYS_I2C_SLAVE           0x0
-#define CONFIG_SYS_I2C_SPEED           100000
-
-/* Environment in SPI NOR flash */
-
-#define CONFIG_SYS_NETA_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII
 
 /* PCIe support */
 #ifndef CONFIG_SPL_BUILD
 #define CONFIG_PCI_SCAN_SHOW
 #endif
 
-/* USB/EHCI/XHCI configuration */
-
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
-
-/* FIXME: broken XHCI support
- * Below defines should enable support for the two rear USB3 ports. Sadly, this
- * does not work because:
- * - xhci-pci seems to not support DM_USB, so with that enabled it is not
- *   found.
- * - USB init fails, controller does not respond in time */
-
-#if !defined(CONFIG_USB_XHCI_HCD)
-#define CONFIG_EHCI_IS_TDI
-#endif
-
-/* why is this only defined in mv-common.h if CONFIG_DM is undefined? */
-
 /*
  * mv-common.h should be defined after CMD configs since it used them
  * to enable certain macros
@@ -75,28 +45,23 @@
 
 /* SPL */
 /* Defines for SPL */
-#define CONFIG_SPL_MAX_SIZE            ((128 << 10) - 0x4030)
 
 #define CONFIG_SPL_BSS_START_ADDR      (0x40000000 + (128 << 10))
-#define CONFIG_SPL_BSS_MAX_SIZE                (16 << 10)
-
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MALLOC_SIMPLE
-#endif
 
-#define CONFIG_SPL_STACK               (0x40000000 + ((192 - 16) << 10))
-#define CONFIG_SPL_BOOTROM_SAVE                (CONFIG_SPL_STACK + 4)
+/* Default Environment */
 
-#if defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI)
-/* SPL related SPI defines */
-#define CONFIG_SYS_U_BOOT_OFFS         CONFIG_SYS_SPI_U_BOOT_OFFS
-#endif
+#define CONFIG_EXTRA_ENV_SETTINGS                              \
+       "initrd_high=0xffffffff\0"                              \
+       "ramdisk_addr_r=0x8000000\0"                            \
+       "usb0Mode=host\0usb1Mode=host\0usb2Mode=device\0"       \
+       "ethmtu=1500\0eth1mtu=1500\0"                           \
+       "update_uboot=sf probe; dhcp; "                         \
+               "mw.b ${loadaddr} 0x0 0xd0000; "                \
+               "tftpboot ${loadaddr} u-boot-spl.kwb; "         \
+               "sf update ${loadaddr} 0x0 0xd0000\0"
 
-/* DS414 bus width is 32bits */
-#define CONFIG_DDR_32BIT
 
-/* Default Environment */
-#define CONFIG_BOOTCOMMAND     "sf read ${loadaddr} 0xd0000 0x700000; bootm"
-#define CONFIG_LOADADDR                0x80000
+/* increase autoneg timeout, my NIC sucks */
+#define PHY_ANEG_TIMEOUT       16000
 
 #endif /* _CONFIG_SYNOLOGY_DS414_H */