Convert CONFIG_CMD_IDE to Kconfig

[platform/kernel/u-boot.git] / include / configs / digsy_mtc.h

diff --git a/include/configs/digsy_mtc.h b/include/configs/digsy_mtc.h
index 0bf5088..7800e81 100644 (file)
--- a/include/configs/digsy_mtc.h
+++ b/include/configs/digsy_mtc.h
@@ -22,7 +22,6 @@
 
 #define CONFIG_MPC5200         1       /* This is an MPC5200 CPU */
 #define CONFIG_DIGSY_MTC       1       /* ... on InterControl digsyMTC board */
-#define CONFIG_DISPLAY_BOARDINFO
 
 /*
  * Valid values for CONFIG_SYS_TEXT_BASE are:
@@ -42,7 +41,6 @@
  * Serial console configuration
  */
 #define CONFIG_PSC_CONSOLE     4       /* console is on PSC4  */
-#define CONFIG_BAUDRATE                115200  /* ... at 115200  bps  */
 #define CONFIG_SYS_BAUDRATE_TABLE      \
        { 9600, 19200, 38400, 57600, 115200, 230400 }
 
@@ -51,8 +49,6 @@
  * 0x40000000 - 0x4fffffff - PCI Memory
  * 0x50000000 - 0x50ffffff - PCI IO Space
  */
-#define CONFIG_PCI             1
-#define CONFIG_PCI_PNP         1
 #define CONFIG_PCI_SCAN_SHOW   1
 #define CONFIG_PCI_BOOTDELAY   250
 
@@ -64,27 +60,18 @@
 #define CONFIG_PCI_IO_PHYS     CONFIG_PCI_IO_BUS
 #define CONFIG_PCI_IO_SIZE     0x01000000
 
-/*
- *  Partitions
- */
-#define CONFIG_DOS_PARTITION
 #define CONFIG_BZIP2
 
 /*
  * Video
  */
-#define CONFIG_VIDEO
 
 #ifdef CONFIG_VIDEO
 #define CONFIG_VIDEO_MB862xx
 #define CONFIG_VIDEO_MB862xx_ACCEL
 #define CONFIG_VIDEO_CORALP
-#define CONFIG_CFB_CONSOLE
 #define CONFIG_VIDEO_LOGO
 #define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_VIDEO_SW_CURSOR
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
 #define CONFIG_SPLASH_SCREEN
 #define CONFIG_VIDEO_BMP_GZIP
 #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20)       /* decompressed img */
@@ -98,18 +85,7 @@
 /*
  * Command line configuration.
  */
-#ifdef CONFIG_VIDEO
-#define CONFIG_CMD_BMP
-#endif
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_IDE
 #define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SAVES
@@ -121,7 +97,6 @@
 /*
  * Autobooting
  */
-#define CONFIG_BOOTDELAY       1
 
 #undef CONFIG_BOOTARGS
 
@@ -229,42 +204,6 @@
 #define CONFIG_BOOTCOMMAND     "run mtcb_start"
 
 /*
- * SPI configuration
- */
-#define CONFIG_HARD_SPI                1
-#define CONFIG_MPC52XX_SPI     1
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C                1
-#define CONFIG_SYS_I2C_MODULE  1
-#define CONFIG_SYS_I2C_SPEED   100000
-#define CONFIG_SYS_I2C_SLAVE   0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR             0x50    /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  70
-
-/*
- * RTC configuration
- */
-#if defined(CONFIG_DIGSY_REV5)
-#define CONFIG_SYS_I2C_RTC_ADDR        0x56
-#define CONFIG_RTC_RV3029
-/* Enable 5k Ohm trickle charge resistor */
-#define CONFIG_SYS_RV3029_TCR  0x20
-#else
-#define CONFIG_RTC_DS1337
-#define CONFIG_SYS_I2C_RTC_ADDR        0x68
-#define CONFIG_SYS_DS1339_TCR_VAL      0xAB    /* diode + 4k resistor */
-#endif
-
-/*
  * Flash configuration
  */
 #define        CONFIG_SYS_FLASH_CFI            1
@@ -384,7 +323,6 @@
 #define CONFIG_CMDLINE_EDITING 1
 
 #define CONFIG_MX_CYCLIC       1
-#define CONFIG_ZERO_BOOTDELAY_CHECK
 
 #define CONFIG_SYS_CBSIZE              1024
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
@@ -441,7 +379,6 @@
  */
 #define CONFIG_USB_OHCI_NEW
 #define CONFIG_SYS_OHCI_BE_CONTROLLER
-#define CONFIG_USB_STORAGE
 
 #define CONFIG_USB_CLOCK       0x00013333
 #define CONFIG_USB_CONFIG      0x00002000