#define __CONFIG_H
/* High Level Configuration Options */
-#define CONFIG_ARMV7 1 /* This is an ARM V7 CPU core */
#define CONFIG_OMAP 1 /* in a TI OMAP core */
#define CONFIG_OMAP34XX 1 /* which is a 34XX */
-#define CONFIG_OMAP3430 1 /* which is in a 3430 */
#define CONFIG_OMAP3_DEVKIT8000 1 /* working with DevKit8000 */
+#define CONFIG_MACH_TYPE MACH_TYPE_DEVKIT8000
+#define CONFIG_OMAP_GPIO
-#define CONFIG_SYS_TEXT_BASE 0x80008000
+/*
+ * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
+ * 64 bytes before this address should be set aside for u-boot.img's
+ * header. That is 0x800FFFC0--0x80100000 should not be used for any
+ * other needs.
+ */
+#define CONFIG_SYS_TEXT_BASE 0x80100000
#define CONFIG_SDRC /* The chip has SDRC controller */
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
-#undef CONFIG_USE_IRQ /* no support for IRQs */
#define CONFIG_MISC_INIT_R
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
#define CONFIG_INITRD_TAG 1
#define CONFIG_REVISION_TAG 1
+#define CONFIG_OF_LIBFDT 1
+
/* Size of malloc() pool */
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
/* Sector */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
- /* initial data */
/* Hardware drivers */
-
-/* DDR - I use Micron DDR */
-#define CONFIG_OMAP3_MICRON_DDR 1
-
/* DM9000 */
-#define CONFIG_NET_MULTI 1
#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_DRIVER_DM9000 1
#define CONFIG_DM9000_BASE 0x2c000000
115200}
/* MMC */
+#define CONFIG_GENERIC_MMC 1
#define CONFIG_MMC 1
-#define CONFIG_OMAP3_MMC 1
+#define CONFIG_OMAP_HSMMC 1
#define CONFIG_DOS_PARTITION 1
/* I2C */
#define CONFIG_HARD_I2C 1
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_SLAVE 1
-#define CONFIG_SYS_I2C_BUS 0
-#define CONFIG_SYS_I2C_BUS_SELECT 1
#define CONFIG_DRIVER_OMAP34XX_I2C 1
/* TWL4030 */
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x82000000\0" \
- "console=ttyS2,115200n8\0" \
+ "console=ttyO2,115200n8\0" \
+ "mmcdev=0\0" \
"vram=12M\0" \
"dvimode=1024x768MR-16@60\0" \
"defaultdisplay=dvi\0" \
"run commonargs; " \
"setenv bootargs ${bootargs} " \
"root=/dev/mmcblk0p2 " \
+ "rootwait " \
"${kernelopts}\0" \
"nandargs=" \
"run commonargs; " \
"${kernelopts} " \
"dnsip1=${dnsip} " \
"dnsip2=${dnsip2}\0" \
- "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+ "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source ${loadaddr}\0" \
- "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+ "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
"eraseenv=nand unlock 0x260000 0x20000; nand erase 0x260000 0x20000\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"dhcp ${loadaddr}; " \
"run netargs; " \
"bootm ${loadaddr}\0" \
- "autoboot=if mmc init 0; then " \
+ "autoboot=mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
#define CONFIG_AUTO_COMPLETE 1
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_PROMPT "OMAP3 DevKit8000 # "
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
#define CONFIG_SYS_HZ 1000
-/* The stack sizes are set up in start.S using the settings below */
-#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
-#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack 4 KiB */
-#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack 4 KiB */
-#endif
-
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE (128 << 20) /* at least 128 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
-/* SDRAM Bank Allocation method */
-#define SDRC_R_B_C 1
-
/* NAND and environment organization */
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
+/* SRAM config */
+#define CONFIG_SYS_SRAM_START 0x40200000
+#define CONFIG_SYS_SRAM_SIZE 0x10000
+
+/* Defines for SPL */
+#define CONFIG_SPL
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_NAND_SIMPLE
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
+#define CONFIG_SPL_POWER_SUPPORT
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
+#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
+#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
+
+#define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/
+#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */
+#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
+
+#define CONFIG_SPL_BSS_START_ADDR 0x80000500 /* leave space for bootargs*/
+#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
+
+/* NAND boot config */
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_COUNT 64
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
+#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
+ 10, 11, 12, 13}
+
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 3
+
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x200000
+
+#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */
+
+/* SPL OS boot options */
+#define CONFIG_SPL_OS_BOOT
+
+#define CONFIG_CMD_SPL
+#define CONFIG_CMD_SPL_WRITE_SIZE 0x400 /* 1024 byte */
+#define CONFIG_CMD_SPL_NAND_OFS (CONFIG_SYS_NAND_SPL_KERNEL_OFFS+\
+ 0x400000)
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
+#define CONFIG_SYS_SPL_ARGS_ADDR (PHYS_SDRAM_1 + 0x100)
+
#endif /* __CONFIG_H */