CONFIG_SYS_[DI]CACHE_OFF: convert to Kconfig

[platform/kernel/u-boot.git] / include / configs / devkit3250.h

diff --git a/include/configs/devkit3250.h b/include/configs/devkit3250.h
index 913b948..c93a5de 100644 (file)
--- a/include/configs/devkit3250.h
+++ b/include/configs/devkit3250.h
@@ -1,9 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Embest/Timll DevKit3250 board configuration file
  *
  * Copyright (C) 2011-2015 Vladimir Zapolskiy <vz@mleia.com>
- *
- * SPDX-License-Identifier:    GPL-2.0+
  */
 
 #ifndef __CONFIG_DEVKIT3250_H__
@@ -13,27 +12,18 @@
 #include <linux/sizes.h>
 #include <asm/arch/cpu.h>
 
-/*
- * Define DevKit3250 machine type by hand until it lands in mach-types
- */
-#define MACH_TYPE_DEVKIT3250           3697
 #define CONFIG_MACH_TYPE               MACH_TYPE_DEVKIT3250
 
-#define CONFIG_SYS_ICACHE_OFF
-#define CONFIG_SYS_DCACHE_OFF
 #if !defined(CONFIG_SPL_BUILD)
 #define CONFIG_SKIP_LOWLEVEL_INIT
 #endif
-#define CONFIG_BOARD_EARLY_INIT_F
 
 /*
  * Memory configurations
  */
-#define CONFIG_NR_DRAM_BANKS           1
 #define CONFIG_SYS_MALLOC_LEN          SZ_1M
 #define CONFIG_SYS_SDRAM_BASE          EMC_DYCS0_BASE
 #define CONFIG_SYS_SDRAM_SIZE          SZ_64M
-#define CONFIG_SYS_TEXT_BASE           0x83F00000
 #define CONFIG_SYS_MEMTEST_START       (CONFIG_SYS_SDRAM_BASE + SZ_32K)
 #define CONFIG_SYS_MEMTEST_END         (CONFIG_SYS_TEXT_BASE - SZ_1M)
 
@@ -46,7 +36,6 @@
  * Serial Driver
  */
 #define CONFIG_SYS_LPC32XX_UART                5   /* UART5 */
-#define CONFIG_BAUDRATE                        115200
 
 /*
  * DMA
@@ -70,7 +59,6 @@
 /*
  * SSP/SPI
  */
-#define CONFIG_LPC32XX_SSP
 #define CONFIG_LPC32XX_SSP_TIMEOUT     100000
 
 /*
@@ -79,8 +67,6 @@
 #define CONFIG_RMII
 #define CONFIG_PHY_SMSC
 #define CONFIG_LPC32XX_ETH
-#define CONFIG_PHYLIB
-#define CONFIG_PHY_ADDR                        0x1F
 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
 
 /*
@@ -90,12 +76,10 @@
 #define CONFIG_SYS_MAX_FLASH_SECT      71
 #define CONFIG_SYS_FLASH_BASE          EMC_CS0_BASE
 #define CONFIG_SYS_FLASH_SIZE          SZ_4M
-#define CONFIG_SYS_FLASH_CFI
 
 /*
  * NAND controller
  */
-#define CONFIG_NAND_LPC32XX_SLC
 #define CONFIG_SYS_NAND_BASE           SLC_NAND_BASE
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
 #define CONFIG_SYS_NAND_BASE_LIST      { CONFIG_SYS_NAND_BASE }
@@ -116,32 +100,18 @@
 #define CONFIG_SYS_NAND_PAGE_SIZE              NAND_LARGE_BLOCK_PAGE_SIZE
 #define CONFIG_SYS_NAND_USE_FLASH_BBT
 
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NAND
-
 /*
  * USB
  */
 #define CONFIG_USB_OHCI_LPC32XX
 #define CONFIG_USB_ISP1301_I2C_ADDR            0x2d
-#define CONFIG_USB_STORAGE
 
 /*
  * U-Boot General Configurations
  */
-#define CONFIG_SYS_LONGHELP
 #define CONFIG_SYS_CBSIZE              1024
-#define CONFIG_SYS_PBSIZE              \
-       (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS             16
 #define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE
 
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_VERSION_VARIABLE
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DOS_PARTITION
-
 /*
  * Pass open firmware flat tree
  */
@@ -149,7 +119,6 @@
 /*
  * Environment
  */
-#define CONFIG_ENV_IS_IN_NAND          1
 #define CONFIG_ENV_SIZE                        SZ_128K
 #define CONFIG_ENV_OFFSET              0x000A0000
 
@@ -178,35 +147,24 @@
  */
 #define CONFIG_CMDLINE_TAG
 #define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-#define CONFIG_BOOTDELAY               1
 
 #define CONFIG_BOOTFILE                        "uImage"
-#define CONFIG_BOOTARGS                        "console=ttyS0,115200n8"
 #define CONFIG_LOADADDR                        0x80008000
 
 /*
  * SPL specific defines
  */
 /* SPL will be executed at offset 0 */
-#define CONFIG_SPL_TEXT_BASE           0x00000000
 
 /* SPL will use SRAM as stack */
 #define CONFIG_SPL_STACK               0x0000FFF8
-#define CONFIG_SPL_BOARD_INIT
 
 /* Use the framework and generic lib */
-#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
 
 /* SPL will use serial */
-#define CONFIG_SPL_SERIAL_SUPPORT
 
 /* SPL loads an image from NAND */
-#define CONFIG_SPL_NAND_SIMPLE
 #define CONFIG_SPL_NAND_RAW_ONLY
-#define CONFIG_SPL_NAND_SUPPORT
 #define CONFIG_SPL_NAND_DRIVERS
 
 #define CONFIG_SPL_NAND_ECC