#define CONFIG_SYS_MALLOC_LEN SZ_1M
#define CONFIG_SYS_SDRAM_BASE EMC_DYCS0_BASE
#define CONFIG_SYS_SDRAM_SIZE SZ_64M
-#define CONFIG_SYS_TEXT_BASE 0x83FA0000
+#define CONFIG_SYS_TEXT_BASE 0x83F00000
#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + SZ_32K)
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_TEXT_BASE - SZ_1M)
#define CONFIG_BAUDRATE 115200
/*
+ * DMA
+ */
+#if !defined(CONFIG_SPL_BUILD)
+#define CONFIG_DMA_LPC32XX
+#endif
+
+/*
* I2C
*/
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_LPC32XX
#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_CMD_I2C
/*
* GPIO
*/
#define CONFIG_LPC32XX_GPIO
-#define CONFIG_CMD_GPIO
/*
* SSP/SPI
*/
#define CONFIG_LPC32XX_SSP
#define CONFIG_LPC32XX_SSP_TIMEOUT 100000
-#define CONFIG_CMD_SPI
/*
* Ethernet
#define CONFIG_PHYLIB
#define CONFIG_PHY_ADDR 0x1F
#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
/*
* NOR Flash
#define CONFIG_LPC32XX_NAND_SLC_RHOLD 200000000
#define CONFIG_LPC32XX_NAND_SLC_RSETUP 50000000
+#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000
+#define CONFIG_SYS_NAND_PAGE_SIZE NAND_LARGE_BLOCK_PAGE_SIZE
#define CONFIG_SYS_NAND_USE_FLASH_BBT
+
+#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_NAND
/*
+ * USB
+ */
+#define CONFIG_USB_OHCI_LPC32XX
+#define CONFIG_USB_ISP1301_I2C_ADDR 0x2d
+
+/*
* U-Boot General Configurations
*/
#define CONFIG_SYS_LONGHELP
#define CONFIG_AUTO_COMPLETE
#define CONFIG_CMDLINE_EDITING
-#define CONFIG_VERSION_VARIABLE
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DOS_PARTITION
/*
* Pass open firmware flat tree
*/
-#define CONFIG_OF_LIBFDT
/*
* Environment
/*
* U-Boot Commands
*/
-#define CONFIG_CMD_CACHE
/*
* Boot Linux
*/
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-#define CONFIG_BOOTDELAY 1
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_BOOTARGS "console=ttyS0,115200n8"
/* Use the framework and generic lib */
#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
/* SPL will use serial */
-#define CONFIG_SPL_SERIAL_SUPPORT
/* SPL loads an image from NAND */
#define CONFIG_SPL_NAND_SIMPLE
#define CONFIG_SPL_NAND_RAW_ONLY
-#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_NAND_DRIVERS
-#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000
-#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
-#define CONFIG_SYS_NAND_ECCSIZE 0x100
-#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SYS_NAND_ECCPOS { 40, 41, 42, 43, 44, 45, 46, 47, \
- 48, 49, 50, 51, 52, 53, 54, 55, \
- 56, 57, 58, 59, 60, 61, 62, 63, }
-#define CONFIG_SYS_NAND_ECCBYTES 3
-#define CONFIG_SYS_NAND_PAGE_COUNT 64
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
-
#define CONFIG_SPL_NAND_ECC
#define CONFIG_SPL_NAND_SOFTECC