* (C) Copyright 2001, 2002
* Sangmoon Kim, Etin Systems, dogoil@etinsys.com.
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
/* ------------------------------------------------------------------------- */
#undef CONFIG_SYS_AUTOLOAD
/* rootpath */
-#define CONFIG_ROOTPATH /tftpboot/target
+#define CONFIG_ROOTPATH "/tftpboot/target"
/* gatewayip */
#define CONFIG_GATEWAYIP 192.168.0.1
#define CONFIG_HOSTNAME debris
/* bootfile */
-#define CONFIG_BOOTFILE pImage
+#define CONFIG_BOOTFILE "pImage"
/* loadaddr */
#define CONFIG_LOADADDR 800000
#define CONFIG_CMD_ELF
#define CONFIG_CMD_I2C
#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_KGBD
+#define CONFIG_CMD_KGDB
#define CONFIG_CMD_PCI
#define CONFIG_CMD_PING
#define CONFIG_CMD_SAVES
*-----------------------------------------------------------------------
*/
#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
#define CONFIG_PCI_PNP
-#define CONFIG_NET_MULTI /* Multi ethernet cards support */
#define CONFIG_EEPRO100
#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_EEPRO100_SROM_WRITE
* configuration items that the driver uses to drive the port pins.
*/
#define CONFIG_HARD_I2C 1 /* To enable I2C support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE 0x7F
-#ifdef CONFIG_SOFT_I2C
+#ifdef CONFIG_SYS_I2C_SOFT
#error "Soft I2C is not configured properly. Please review!"
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT_SPEED 50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F
#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
#define I2C_ACTIVE (iop->pdir |= 0x00010000)
#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
else iop->pdat &= ~0x00020000
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-#endif /* CONFIG_SOFT_I2C */
+#endif /* CONFIG_SYS_I2C_SOFT */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 /* EEPROM IS24C02 */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CONFIG_SYS_FLASH_BANKS { FLASH_BASE0_PRELIM }
/*-----------------------------------------------------------------------