/*
- * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ * Copyright (C) 2014-2015 Stefan Roese <sr@denx.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* High Level Configuration Options (easy to change)
*/
-#define CONFIG_ARMADA_XP /* SOC Family Name */
#define CONFIG_DB_784MP_GP /* Board target name for DDR training */
-#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_DISPLAY_BOARDINFO_LATE
-#define CONFIG_SYS_TEXT_BASE 0x04000000
+/*
+ * TEXT_BASE needs to be below 16MiB, since this area is scrubbed
+ * for DDR ECC byte filling in the SPL before loading the main
+ * U-Boot into it.
+ */
+#define CONFIG_SYS_TEXT_BASE 0x00800000
#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
/*
* Commands configuration
*/
-#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
-#include <config_cmd_default.h>
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ENV
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SF
-#define CONFIG_CMD_SPI
-#define CONFIG_CMD_TFTPPUT
-#define CONFIG_CMD_TIME
+#define CONFIG_CMD_PCI
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_SLAVE 0x0
#define CONFIG_SYS_I2C_SPEED 100000
+/* USB/EHCI configuration */
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 3
+
/* SPI NOR flash default params, used by sf commands */
#define CONFIG_SF_DEFAULT_SPEED 1000000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3
-#define CONFIG_SPI_FLASH_STMICRO
/* Environment in SPI NOR flash */
-#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_OFFSET (1 << 20) /* 1MiB in */
#define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */
#define CONFIG_ENV_SECT_SIZE (64 << 10) /* 64KiB sectors */
#define CONFIG_PHY_MARVELL /* there is a marvell phy */
-#define CONFIG_PHY_BASE_ADDR 0x10
-#define CONFIG_SYS_NETA_INTERFACE_TYPE PHY_INTERFACE_MODE_QSGMII
#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */
-#define CONFIG_RESET_PHY_R
-#define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup */
#define CONFIG_SYS_ALT_MEMTEST
+/* SATA support */
+#define CONFIG_SYS_SATA_MAX_DEVICE 2
+#define CONFIG_SATA_MV
+#define CONFIG_LIBATA
+#define CONFIG_LBA48
+
+/* Additional FS support/configuration */
+#define CONFIG_SUPPORT_VFAT
+
+/* PCIe support */
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_PCI_MVEBU
+#define CONFIG_PCI_SCAN_SHOW
+#endif
+
+/* NAND */
+#define CONFIG_SYS_NAND_USE_FLASH_BBT
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
/*
* mv-common.h should be defined after CMD configs since it used them
* to enable certain macros
#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + (128 << 10))
#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)
-#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
- CONFIG_SPL_BSS_MAX_SIZE)
-#define CONFIG_SYS_SPL_MALLOC_SIZE (16 << 10)
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MALLOC_SIMPLE
+#endif
#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10))
#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_I2C_SUPPORT
-#define CONFIG_SPL_LDSCRIPT "arch/arm/mvebu-common/u-boot-spl.lds"
-
/* SPL related SPI defines */
-#define CONFIG_SPL_SPI_SUPPORT
-#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SPL_SPI_BUS 0
-#define CONFIG_SPL_SPI_CS 0
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
+#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS
/* Enable DDR support in SPL (DDR3 training from Marvell bin_hdr) */
-#define CONFIG_SYS_MVEBU_DDR
#define CONFIG_SPD_EEPROM 0x4e
+#define CONFIG_BOARD_ECC_SUPPORT /* this board supports ECC */
#endif /* _CONFIG_DB_MV7846MP_GP_H */