* (C) Copyright 2004
* Tolunay Orkun, Nextio Inc., torkun@nextio.com
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
/*
*
*/
#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " /* hush shell secondary prompt */
-#endif
#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_info (bd_t) */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
* I2C configuration
*
*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
-#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */
-#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave address */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F /* I2C slave address */
/*
* MII PHY configuration
#define CONFIG_PHY_CMD_DELAY 40 /* PHY COMMAND delay */
/* 32usec min. for LXT971A */
#define CONFIG_PHY_RESET_DELAY 300 /* PHY RESET recovery delay */
-#define CONFIG_NET_MULTI
/*
* RTC configuration
*
*/
#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
#define PCI_HOST_FORCE 1 /* configure as pci host */
#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
*
*/
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of on-chip SRAM */
-#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* byte size reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*
#define CONFIG_SYS_I2C_PLL_ADDR 0x58 /* I2C address of AMIS FS6377-01 PLL */
#define CONFIG_I2CFAST 1 /* enable "i2cfast" env. setting */
-/*
- * Internal Definitions
- *
- * Boot Flags
- *
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
#endif /* __CONFIG_H */