#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
+/* we will never enable dcache, because we have to setup MMU first */
+#define CONFIG_SYS_DCACHE_OFF
+#define CONFIG_SYS_TEXT_BASE 0x0
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
/*
* Hardware drivers
*/
-#define CONFIG_DRIVER_SMC91111
+#define CONFIG_SMC91111
#define CONFIG_SMC91111_BASE 0x10000300
#define CONFIG_SMC91111_EXT_PHY
#define CONFIG_SMC_USE_32_BIT
/*
* select serial console configuration
*/
+#define CONFIG_PXA_SERIAL
#define CONFIG_FFUART 1 /* we use FFUART on LUBBOCK */
/* allow to overwrite serial and ethaddr */
#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
#define CONFIG_SYS_LOAD_ADDR 0xa2000000 /* default load address */
-#define CONFIG_SYS_HZ 3686400 /* incrementer freq: 3.6864 MHz */
+#define CONFIG_SYS_HZ 1000
#define CONFIG_SYS_CPUSPEED 0x141 /* set core clock to 200/200/100 MHz */
/* valid baudrates */
/*
* Physical Memory Map
*/
-#define CONFIG_NR_DRAM_BANKS 4 /* we have 2 banks of DRAM */
+#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */
#define PHYS_SDRAM_1_SIZE 0x01000000 /* 64 MB */
-#define PHYS_SDRAM_2 0xa4000000 /* SDRAM Bank #2 */
-#define PHYS_SDRAM_2_SIZE 0x00000000 /* 0 MB */
-#define PHYS_SDRAM_3 0xa8000000 /* SDRAM Bank #3 */
-#define PHYS_SDRAM_3_SIZE 0x00000000 /* 0 MB */
-#define PHYS_SDRAM_4 0xac000000 /* SDRAM Bank #4 */
-#define PHYS_SDRAM_4_SIZE 0x00000000 /* 0 MB */
#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
#define PHYS_FLASH_2 0x04000000 /* Flash Bank #1 */
#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR (GENERATED_GBL_DATA_SIZE + PHYS_SDRAM_1)
+
/*
* FLASH and environment organization
*/
* Clocks, power control and interrupts
*/
#define CONFIG_SYS_PSSR_VAL 0x00000020
-#define CONFIG_SYS_CCCR_VAL 0x00000141 /* 100 MHz memory, 200 MHz CPU */
-#define CONFIG_SYS_CKEN_VAL 0x00000060 /* FFUART and STUART enabled */
-#define CONFIG_SYS_ICMR_VAL 0x00000000 /* No interrupts enabled */
+#define CONFIG_SYS_CCCR 0x00000141 /* 100 MHz memory, 200 MHz CPU */
+#define CONFIG_SYS_CKEN 0x00000060 /* FFUART and STUART enabled */
+#define CONFIG_SYS_ICMR 0x00000000 /* No interrupts enabled */
/* FIXME
*
#define CONFIG_SYS_MDMRS_VAL 0x00000000
#define CONFIG_SYS_MDREFR_VAL 0x00403018 /* Initial setting, individual bits set in lowlevel_init.S */
#endif
+#define CONFIG_SYS_FLYCNFG_VAL 0x00000000
+#define CONFIG_SYS_SXCNFG_VAL 0x00000000
/*
* PCMCIA and CF Interfaces (NOT USED, these values from lubbock init)
#define LED_IRDA1 2
#define LED_IRDA2 4
#define LED_IRDA3 6
-#define CRADLE_LED_SET_REG GPSR2
-#define CRADLE_LED_CLR_REG GPCR2
/* SuperIO defines */
#define CRADLE_SIO_INDEX 0x2e
projects / platform / kernel / u-boot.git / blobdiff