*/
#define CONFIG_CUSTOMER_BOARD_SUPPORT
-#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-
/*
* TEXT_BASE needs to be below 16MiB, since this area is scrubbed
* for DDR ECC byte filling in the SPL before loading the main
* U-Boot into it.
*/
-#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
-
-#define CONFIG_LOADADDR 1000000
-
-/*
- * SDIO/MMC Card Configuration
- */
-#define CONFIG_SYS_MMC_BASE MVEBU_SDIO_BASE
-
-/*
- * SATA/SCSI/AHCI configuration
- */
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
- CONFIG_SYS_SCSI_MAX_LUN)
-
-/* USB/EHCI configuration */
-#define CONFIG_EHCI_IS_TDI
-
/* Environment in SPI NOR flash */
#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */
#define CONFIG_SPL_STACK (0x40000000 + ((212 - 16) << 10))
#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_I2C_SUPPORT
-
-#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH
-/* SPL related SPI defines */
-#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS
-#endif
-
#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD
/* SPL related MMC defines */
-#define CONFIG_SPL_MMC_SUPPORT
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 1
-#define CONFIG_SYS_MMC_U_BOOT_OFFS (168 << 10)
-#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_MMC_U_BOOT_OFFS
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR (CONFIG_SYS_U_BOOT_OFFS / 512)
#ifdef CONFIG_SPL_BUILD
#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER 0x00180000 /* in SDRAM */
#endif
/*
* Environment Configuration
*/
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_BAUDRATE 115200
#define CONFIG_HOSTNAME "ccdc"
#define CONFIG_ROOTPATH "/opt/nfsroot"
-#define CONFIG_BOOTFILE "ccdc.img"
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth1\0" \
" gpio clear ${gpio1}; gpio set ${gpio2};" \
" fi; sleep 0.12; done\0"
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off " \
- "console=${consoledev},${baudrate} ${othbootargs}; " \
- "tftpboot ${bootfile_addr} ${bootfile}; " \
- "bootm ${bootfile_addr}"
-
-#define CONFIG_MMCBOOTCOMMAND \
- "setenv bootargs root=/dev/mmcblk0p3 rw rootwait " \
- "console=${consoledev},${baudrate} ${othbootargs}; " \
- "ext2load mmc 0:2 ${bootfile_addr} ${bootfile}; " \
- "bootm ${bootfile_addr}"
-
-#define CONFIG_BOOTCOMMAND \
- "if env exists keyprogram; then;" \
- " setenv keyprogram; run nfsboot;" \
- " fi;" \
- " run dobootfail"
-
/*
* mv-common.h should be defined after CMD configs since it used them
* to enable certain macros