Convert CONFIG_SPL_PAD_TO et al to Kconfig

[platform/kernel/u-boot.git] / include / configs / controlcenterdc.h

diff --git a/include/configs/controlcenterdc.h b/include/configs/controlcenterdc.h
index efd04c6..94f61f9 100644 (file)
--- a/include/configs/controlcenterdc.h
+++ b/include/configs/controlcenterdc.h
@@ -8,28 +8,11 @@
 #define _CONFIG_CONTROLCENTERDC_H
 
 /*
- * High Level Configuration Options (easy to change)
- */
-#define CONFIG_CUSTOMER_BOARD_SUPPORT
-
-/*
  * TEXT_BASE needs to be below 16MiB, since this area is scrubbed
  * for DDR ECC byte filling in the SPL before loading the main
  * U-Boot into it.
  */
 
-/*
- * SATA/SCSI/AHCI configuration
- */
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID    2
-#define CONFIG_SYS_SCSI_MAX_LUN                1
-#define CONFIG_SYS_SCSI_MAX_DEVICE     (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
-                                        CONFIG_SYS_SCSI_MAX_LUN)
-
-/* USB/EHCI configuration */
-#define CONFIG_EHCI_IS_TDI
-
 /* Environment in SPI NOR flash */
 
 #define PHY_ANEG_TIMEOUT       8000    /* PHY needs a longer aneg time */
@@ -39,11 +22,6 @@
 #define CONFIG_PCI_SCAN_SHOW
 #endif
 
-/*
- * Software (bit-bang) MII driver configuration
- */
-#define CONFIG_BITBANGMII_MULTI
-
 /* SPL */
 /*
  * Select the boot device here
@@ -59,12 +37,6 @@
 /* Defines for SPL */
 #define CONFIG_SPL_SIZE                        (160 << 10)
 
-#if defined(CONFIG_SECURED_MODE_IMAGE)
-#define CONFIG_SPL_MAX_SIZE            (CONFIG_SPL_SIZE - 0x2614)
-#else
-#define CONFIG_SPL_MAX_SIZE            (CONFIG_SPL_SIZE - 0x30)
-#endif
-
 #define CONFIG_SPL_BSS_START_ADDR      (0x40000000 + CONFIG_SPL_SIZE)
 #define CONFIG_SPL_BSS_MAX_SIZE                (16 << 10)
 
@@ -75,13 +47,8 @@
 #define CONFIG_SPL_STACK               (0x40000000 + ((212 - 16) << 10))
 #define CONFIG_SPL_BOOTROM_SAVE                (CONFIG_SPL_STACK + 4)
 
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_I2C
-
 #if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD
 /* SPL related MMC defines */
-#define CONFIG_SPL_MMC
 #ifdef CONFIG_SPL_BUILD
 #define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER      0x00180000      /* in SDRAM */
 #endif
@@ -93,7 +60,6 @@
 
 #define CONFIG_HOSTNAME                "ccdc"
 #define CONFIG_ROOTPATH                "/opt/nfsroot"
-#define CONFIG_BOOTFILE                "ccdc.img"
 
 #define CONFIG_EXTRA_ENV_SETTINGS                                              \
        "netdev=eth1\0"                                         \
@@ -130,26 +96,6 @@
                " gpio clear ${gpio1}; gpio set ${gpio2};"                      \
                " fi; sleep 0.12; done\0"
 
-#define NFSBOOTCOMMAND                                                         \
-       "setenv bootargs root=/dev/nfs rw "                                             \
-       "nfsroot=${serverip}:${rootpath} "                                              \
-       "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off "   \
-       "console=${consoledev},${baudrate} ${othbootargs}; "                            \
-       "tftpboot ${bootfile_addr} ${bootfile}; "                                               \
-       "bootm ${bootfile_addr}"
-
-#define MMCBOOTCOMMAND                                 \
-       "setenv bootargs root=/dev/mmcblk0p3 rw rootwait "      \
-       "console=${consoledev},${baudrate} ${othbootargs}; "    \
-       "ext2load mmc 0:2 ${bootfile_addr} ${bootfile}; "       \
-       "bootm ${bootfile_addr}"
-
-#define CONFIG_BOOTCOMMAND                     \
-       "if env exists keyprogram; then;"       \
-       " setenv keyprogram; run nfsboot;"      \
-        " fi;"                                 \
-        " run dobootfail"
-
 /*
  * mv-common.h should be defined after CMD configs since it used them
  * to enable certain macros