#define CONFIG_SYS_CLK 66000000
#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
-/* Enable Dma Timer */
-#define CONFIG_MCFTMR
-
/* ---
* Define baudrate for UART1 (console output, tftp, ...)
* default value of CONFIG_BAUDRATE for Sentec board: 19200 baud
* ---
*/
-#define CONFIG_MCFUART
#define CONFIG_SYS_UART_PORT (0)
/* ---
*/
#if 0
-#define CONFIG_WATCHDOG
#define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */
#endif
env/embedded.o(.text);
/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-/*
- * Command line configuration.
- */
-
-#ifdef CONFIG_MCFFEC
-# define CONFIG_MII_INIT 1
-# define CONFIG_SYS_DISCOVER_PHY
-# define CONFIG_SYS_RX_ETH_BUFFER 8
-# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
-# ifndef CONFIG_SYS_DISCOVER_PHY
-# define FECDUPLEX FULL
-# define FECSPEED _100BASET
-# else
-# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-# endif
-# endif /* CONFIG_SYS_DISCOVER_PHY */
-#endif
-
-/*
*-----------------------------------------------------------------------------
* Define user parameters that have to be customized most likely
*-----------------------------------------------------------------------------
#if 0
-#define CONFIG_BOOTCOMMAND "bootm 0xffe80000" /*Autoboto command, please
enter a valid image address in flash */
/* User network settings */
#endif
-#define CONFIG_SYS_LOAD_ADDR 0x20000 /*Defines default RAM address
-from which user programs will be started */
-
/*---*/
/*
* ---
*/
-#define CONFIG_SYS_MEMTEST_START 0x400
-#define CONFIG_SYS_MEMTEST_END 0x380000
-
/* ---
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* ---
*/
-#define CONFIG_SYS_DISCOVER_PHY
#define CONFIG_SYS_ENET_BD_BASE 0x780000
/*-----------------------------------------------------------------------
*/
#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
#define CONFIG_SYS_FLASH_BASE 0xffe00000
-#ifdef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_SYS_MONITOR_BASE 0x20000
-#else
-#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
-#endif
-
#define CONFIG_SYS_MONITOR_LEN 0x20000
-#define CONFIG_SYS_MALLOC_LEN (256 << 10)
-#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
/*
* For booting Linux, the board info and command line data
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 11 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 1000 /* flash timeout */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CONFIG_SYS_CACHELINE_SIZE 16
#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - 8)
CF_CACR_EUSP)
/*-----------------------------------------------------------------------
- * Memory bank definitions
- *
- * Please refer also to Motorola Coldfire user manual - Chapter XXX
- * <http://e-www.motorola.com/files/dsp/doc/ref_manual/MCF5272UM.pdf>
- */
-#define CONFIG_SYS_BR0_PRELIM 0xFFE00201
-#define CONFIG_SYS_OR0_PRELIM 0xFFE00014
-
-#define CONFIG_SYS_BR1_PRELIM 0
-#define CONFIG_SYS_OR1_PRELIM 0
-
-#define CONFIG_SYS_BR2_PRELIM 0
-#define CONFIG_SYS_OR2_PRELIM 0
-
-#define CONFIG_SYS_BR3_PRELIM 0
-#define CONFIG_SYS_OR3_PRELIM 0
-
-#define CONFIG_SYS_BR4_PRELIM 0
-#define CONFIG_SYS_OR4_PRELIM 0
-
-#define CONFIG_SYS_BR5_PRELIM 0
-#define CONFIG_SYS_OR5_PRELIM 0
-
-#define CONFIG_SYS_BR6_PRELIM 0
-#define CONFIG_SYS_OR6_PRELIM 0
-
-#define CONFIG_SYS_BR7_PRELIM 0x00000701
-#define CONFIG_SYS_OR7_PRELIM 0xFF00007C
-
-/*-----------------------------------------------------------------------
* LED config
*/
#define LED_STAT_0 0xffff /*all LEDs off*/