* ---
*/
-#define CONFIG_SYS_CLK 66000000
-#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
+#define CFG_SYS_CLK 66000000
+#define CFG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
/* ---
* Define baudrate for UART1 (console output, tftp, ...)
* default value of CONFIG_BAUDRATE for Sentec board: 19200 baud
- * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command
+ * CFG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command
* interface
* ---
*/
-#define CONFIG_SYS_UART_PORT (0)
-
-/* ---
- * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change
- * timeout acc. to your needs
- * #define CONFIG_WATCHDOG_TIMEOUT x , x is timeout in milliseconds, e. g. 10000
- * for 10 sec
- * ---
- */
-
-#if 0
-#define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */
-#endif
-
-/* ---
- * CONFIG_MONITOR_IS_IN_RAM defines if u-boot is started from a different
- * bootloader residing in flash ('chainloading'); if you want to use
- * chainloading or want to compile a u-boot binary that can be loaded into
- * RAM via BDM set
- * "#if 0" to "#if 1"
- * You will need a first stage bootloader then, e. g. colilo or a working BDM
- * cable (Background Debug Mode)
- *
- * Setting #if 0: u-boot will start from flash and relocate itself to RAM
- *
- * Please do not forget to modify the setting of CONFIG_SYS_TEXT_BASE
- * in board/cobra5272/config.mk accordingly (#if 0: 0xffe00000; #if 1: 0x20000)
- *
- * ---
- */
-
-#if 0
-#define CONFIG_MONITOR_IS_IN_RAM /* monitor is started from a preloader */
-#endif
+#define CFG_SYS_UART_PORT (0)
/* ---
* Configuration for environment
/* User network settings */
-#define CONFIG_IPADDR 192.168.100.2 /* default board IP address */
-#define CONFIG_SERVERIP 192.168.100.1 /* default tftp server IP address */
-
#endif
/*---*/
* ---
*/
-#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */
+#define CFG_SYS_MBAR 0x10000000 /* Register Base Addrs */
/* ---
* System Conf. Reg. & System Protection Reg.
* ---
*/
-#define CONFIG_SYS_SCR 0x0003
-#define CONFIG_SYS_SPR 0xffff
-
-/* ---
- * Ethernet settings
- * ---
- */
-
-#define CONFIG_SYS_ENET_BD_BASE 0x780000
+#define CFG_SYS_SCR 0x0003
+#define CFG_SYS_SPR 0xffff
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in internal SRAM)
*/
-#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */
+#define CFG_SYS_INIT_RAM_ADDR 0x20000000
+#define CFG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ * Please note that CFG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CFG_SYS_SDRAM_BASE 0x00000000
/*
*-------------------------------------------------------------------------
*-----------------------------------------------------------------------
*/
-/* #define CONFIG_SYS_SDRAM_SIZE 16 */
+/* #define CFG_SYS_SDRAM_SIZE 16 */
/*
*-----------------------------------------------------------------------
*/
-#define CONFIG_SYS_FLASH_BASE 0xffe00000
-
-#define CONFIG_SYS_MONITOR_LEN 0x20000
+#define CFG_SYS_FLASH_BASE 0xffe00000
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization ??
*/
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_SECT 11 /* max number of sectors on one chip */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 1000 /* flash timeout */
+#define CFG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - 8)
-#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - 4)
-#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI)
-#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \
- CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
+#define ICACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \
+ CFG_SYS_INIT_RAM_SIZE - 8)
+#define DCACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \
+ CFG_SYS_INIT_RAM_SIZE - 4)
+#define CFG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI)
+#define CFG_SYS_CACHE_ACR0 (CFG_SYS_SDRAM_BASE | \
+ CF_ADDRMASK(CFG_SYS_SDRAM_SIZE) | \
CF_ACR_EN | CF_ACR_SM_ALL)
-#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \
+#define CFG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \
CF_CACR_DISD | CF_CACR_INVI | \
CF_CACR_CEIB | CF_CACR_DCM | \
CF_CACR_EUSP)
/*-----------------------------------------------------------------------
* Port configuration (GPIO)
*/
-#define CONFIG_SYS_PACNT 0x00000000 /* PortA control reg.: All pins are external
+#define CFG_SYS_PACNT 0x00000000 /* PortA control reg.: All pins are external
GPIO*/
-#define CONFIG_SYS_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs
+#define CFG_SYS_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs
(1^=output, 0^=input) */
-#define CONFIG_SYS_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */
-#define CONFIG_SYS_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART
+#define CFG_SYS_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */
+#define CFG_SYS_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART
configuration */
-#define CONFIG_SYS_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */
-#define CONFIG_SYS_PBDAT 0x0000 /* PortB value reg. */
-#define CONFIG_SYS_PDCNT 0x00000000 /* PortD control reg. */
+#define CFG_SYS_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */
+#define CFG_SYS_PBDAT 0x0000 /* PortB value reg. */
+#define CFG_SYS_PDCNT 0x00000000 /* PortD control reg. */
#endif /* _CONFIG_COBRA5272_H */