+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Configuation settings for the Sentec Cobra Board.
*
* (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
/* ---
#define CONFIG_SYS_CLK 66000000
#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
-/* ---
- * Enable use of Ethernet
- * ---
- */
-#define CONFIG_MCFFEC
-
/* Enable Dma Timer */
#define CONFIG_MCFTMR
* ---
*/
-#define CONFIG_MCFUART
#define CONFIG_SYS_UART_PORT (0)
-#define CONFIG_BAUDRATE 19200
/* ---
* set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change
*/
#if 0
-#define CONFIG_WATCHDOG
#define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */
#endif
* ---
*/
-#ifndef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_ENV_OFFSET 0x4000
-#define CONFIG_ENV_SECT_SIZE 0x2000
-#define CONFIG_ENV_IS_IN_FLASH 1
-#else
-#define CONFIG_ENV_ADDR 0xffe04000
-#define CONFIG_ENV_SECT_SIZE 0x2000
-#define CONFIG_ENV_IS_IN_FLASH 1
-#endif
-
#define LDS_BOARD_TEXT \
- . = DEFINED(env_offset) ? env_offset : .; \
- common/env_embedded.o (.text);
+ . = DEFINED(env_offset) ? env_offset : .; \
+ env/embedded.o(.text);
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
#ifdef CONFIG_MCFFEC
-# define CONFIG_MII 1
# define CONFIG_MII_INIT 1
# define CONFIG_SYS_DISCOVER_PHY
# define CONFIG_SYS_RX_ETH_BUFFER 8
# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-
-# define CONFIG_SYS_FEC0_PINMUX 0
-# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
-# define MCFFEC_TOUT_LOOP 50000
/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
# ifndef CONFIG_SYS_DISCOVER_PHY
# define FECDUPLEX FULL
/*AUTOBOOT settings - booting images automatically by u-boot after power on*/
-#define CONFIG_BOOTDELAY 5 /* used for autoboot, delay in
-seconds u-boot will wait before starting defined (auto-)boot command, setting
-to -1 disables delay, setting to 0 will too prevent access to u-boot command
-interface: u-boot then has to reflashed */
-
/* The following settings will be contained in the environment block ; if you
want to use a neutral environment all those settings can be manually set in
u-boot: 'set' command */
#if 0
-#define CONFIG_BOOTCOMMAND "bootm 0xffe80000" /*Autoboto command, please
enter a valid image address in flash */
-#define CONFIG_BOOTARGS " " /* default bootargs that are
-considered during boot */
-
/* User network settings */
#define CONFIG_IPADDR 192.168.100.2 /* default board IP address */
#endif
-#define CONFIG_SYS_LOAD_ADDR 0x20000 /*Defines default RAM address
-from which user programs will be started */
-
/*---*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
/*
*-----------------------------------------------------------------------------
* End of user parameters to be customized
* ---
*/
-#define CONFIG_SYS_MEMTEST_START 0x400
-#define CONFIG_SYS_MEMTEST_END 0x380000
-
/* ---
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
#endif
#define CONFIG_SYS_MONITOR_LEN 0x20000
-#define CONFIG_SYS_MALLOC_LEN (256 << 10)
#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
/*
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 11 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 1000 /* flash timeout */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CONFIG_SYS_CACHELINE_SIZE 16
#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - 8)
CF_CACR_EUSP)
/*-----------------------------------------------------------------------
- * Memory bank definitions
- *
- * Please refer also to Motorola Coldfire user manual - Chapter XXX
- * <http://e-www.motorola.com/files/dsp/doc/ref_manual/MCF5272UM.pdf>
- */
-#define CONFIG_SYS_BR0_PRELIM 0xFFE00201
-#define CONFIG_SYS_OR0_PRELIM 0xFFE00014
-
-#define CONFIG_SYS_BR1_PRELIM 0
-#define CONFIG_SYS_OR1_PRELIM 0
-
-#define CONFIG_SYS_BR2_PRELIM 0
-#define CONFIG_SYS_OR2_PRELIM 0
-
-#define CONFIG_SYS_BR3_PRELIM 0
-#define CONFIG_SYS_OR3_PRELIM 0
-
-#define CONFIG_SYS_BR4_PRELIM 0
-#define CONFIG_SYS_OR4_PRELIM 0
-
-#define CONFIG_SYS_BR5_PRELIM 0
-#define CONFIG_SYS_OR5_PRELIM 0
-
-#define CONFIG_SYS_BR6_PRELIM 0
-#define CONFIG_SYS_OR6_PRELIM 0
-
-#define CONFIG_SYS_BR7_PRELIM 0x00000701
-#define CONFIG_SYS_OR7_PRELIM 0xFF00007C
-
-/*-----------------------------------------------------------------------
* LED config
*/
#define LED_STAT_0 0xffff /*all LEDs off*/