* File: cmi_mpc5xx.h
*
* Discription: Config header file for cmi
- * board using an MPC5xx CPU
+ * board using an MPC5xx CPU
*
*/
*/
#define CONFIG_MPC555 1 /* This is an MPC555 CPU */
-#define CONFIG_CMI 1 /* Using the customized cmi board */
+#define CONFIG_CMI 1 /* Using the customized cmi board */
/* Serial Console Configuration */
#define CONFIG_5xx_CONS_SCI1
#define CONFIG_BAUDRATE 57600
-#define CONFIG_COMMANDS (CFG_CMD_MEMORY | CFG_CMD_LOADB | CFG_CMD_REGINFO | \
- CFG_CMD_FLASH | CFG_CMD_LOADS | CFG_CMD_ASKENV | \
- CFG_CMD_BDI | CFG_CMD_CONSOLE | CFG_CMD_ENV | CFG_CMD_RUN | \
- CFG_CMD_IMI)
-/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_NET /* disabeled - causes compile errors */
+
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_LOADS
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_CONSOLE
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_IMI
+
#if 0
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
#else
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#endif
-#define CONFIG_BOOTCOMMAND "go 02034004" /* autoboot command */
+#define CONFIG_BOOTCOMMAND "go 02034004" /* autoboot command */
#define CONFIG_BOOTARGS "" /* Assuming OS Image in 4 flash sector at offset 4004 */
-#define CONFIG_WATCHDOG /* turn on platform specific watchdog */
+#define CONFIG_WATCHDOG /* turn on platform specific watchdog */
#define CONFIG_STATUS_LED 1 /* Enable status led */
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
/*
* Internal Memory Mapped (This is not the IMMR content)
*/
-#define CFG_IMMR 0x01000000 /* Physical start adress of internal memory map */
+#define CFG_IMMR 0x01000000 /* Physical start adress of internal memory map */
/*
* Definitions for initial stack pointer and data area
*/
-#define CFG_INIT_RAM_ADDR (CFG_IMMR + 0x003f9800) /* Physical start adress of internal MPC555 writable RAM */
-#define CFG_INIT_RAM_END (CFG_IMMR + 0x003fffff) /* Physical end adress of internal MPC555 used RAM area */
-#define CFG_GBL_DATA_SIZE 64 /* Size in bytes reserved for initial global data */
+#define CFG_INIT_RAM_ADDR (CFG_IMMR + 0x003f9800) /* Physical start adress of internal MPC555 writable RAM */
+#define CFG_INIT_RAM_END (CFG_IMMR + 0x003fffff) /* Physical end adress of internal MPC555 used RAM area */
+#define CFG_GBL_DATA_SIZE 64 /* Size in bytes reserved for initial global data */
#define CFG_GBL_DATA_OFFSET ((CFG_INIT_RAM_END - CFG_INIT_RAM_ADDR) - CFG_GBL_DATA_SIZE) /* Offset from the beginning of ram */
-#define CFG_INIT_SP_ADDR 0x013fa000 /* Physical start adress of inital stack */
+#define CFG_INIT_SP_ADDR 0x013fa000 /* Physical start adress of inital stack */
/*
* Start addresses for the final memory configuration
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000 /* Monitor won't change memory map */
+#define CFG_SDRAM_BASE 0x00000000 /* Monitor won't change memory map */
#define CFG_FLASH_BASE 0x02000000 /* External flash */
#define PLD_BASE 0x03000000 /* PLD */
#define ANYBUS_BASE 0x03010000 /* Anybus Module */
#define CFG_RESET_ADRESS 0x01000000 /* Adress which causes reset */
-#define CFG_MONITOR_BASE CFG_FLASH_BASE /* TEXT_BASE is defined in the board config.mk file. */
- /* This adress is given to the linker with -Ttext to */
- /* locate the text section at this adress. */
+#define CFG_MONITOR_BASE CFG_FLASH_BASE /* TEXT_BASE is defined in the board config.mk file. */
+ /* This adress is given to the linker with -Ttext to */
+ /* locate the text section at this adress. */
#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
#define CFG_MALLOC_LEN (64 << 10) /* Reserve 128 kB for malloc() */
*/
#define CFG_MAX_FLASH_BANKS 1 /* Max number of memory banks */
-#define CFG_MAX_FLASH_SECT 64 /* Max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 600 /* Timeout for Flash Write (in ms) */
+#define CFG_MAX_FLASH_SECT 64 /* Max number of sectors on one chip */
+#define CFG_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 600 /* Timeout for Flash Write (in ms) */
#define CFG_FLASH_PROTECTION 1 /* Physically section protection on */
-#define CFG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_IS_IN_FLASH 1
-#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_OFFSET 0x00020000 /* Environment starts at this adress */
-#define CFG_ENV_SIZE 0x00010000 /* Set whole sector as env */
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_OFFSET 0x00020000 /* Environment starts at this adress */
+#define CONFIG_ENV_SIZE 0x00010000 /* Set whole sector as env */
+#define CFG_USE_PPCENV /* Environment embedded in sect .ppcenv */
#endif
/*-----------------------------------------------------------------------
*-----------------------------------------------------------------------
* Data show cycle
*/
-#define CFG_SIUMCR (SIUMCR_DBGC00) /* Disable data show cycle */
+#define CFG_SIUMCR (SIUMCR_DBGC00) /* Disable data show cycle */
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register
* Set all bits to 40 Mhz
*
*/
-#define CFG_OSC_CLK ((uint)4000000) /* Oscillator clock is 4MHz */
+#define CFG_OSC_CLK ((uint)4000000) /* Oscillator clock is 4MHz */
#define CFG_PLPRCR (PLPRCR_MF_9 | PLPRCR_DIVF_0)
*-----------------------------------------------------------------------
*
*/
-#define CFG_UMCR (UMCR_FSPEED) /* IMB clock same as U-bus */
+#define CFG_UMCR (UMCR_FSPEED) /* IMB clock same as U-bus */
/*-----------------------------------------------------------------------
* ICTRL - I-Bus Support Control Register
*/
-#define CFG_ICTRL (ICTRL_ISCT_SER_7) /* Take out of serialized mode */
+#define CFG_ICTRL (ICTRL_ISCT_SER_7) /* Take out of serialized mode */
/*-----------------------------------------------------------------------
* USIU - Memory Controller Register
#define CFG_OR2_PRELIM (OR_ADDR_MK_FF)
#define CFG_BR3_PRELIM (PLD_BASE | BR_V | BR_BI | BR_LBDIR | BR_PS_8)
#define CFG_OR3_PRELIM (OR_ADDR_MK_FF | OR_TRLX | OR_BSCY | OR_SCY_8 | \
- OR_ACS_10 | OR_ETHR | OR_CSNT)
+ OR_ACS_10 | OR_ETHR | OR_CSNT)
#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* We don't realign the flash */