#ifndef __CONFIG_CM_T43_H
#define __CONFIG_CM_T43_H
-#define CONFIG_CM_T43
-#define CONFIG_ARCH_CPU_INIT
#define CONFIG_MAX_RAM_BANK_SIZE (2048 << 20) /* 2GB */
#define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */
#endif
/* NAND support */
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_SIZE 2048
-#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 14
-#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW
-#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
- CONFIG_SYS_NAND_PAGE_SIZE)
#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
10, 11, 12, 13, 14, 15, 16, 17, \
18, 19, 20, 21, 22, 23, 24, 25, \
42, 43, 44, 45, 46, 47, 48, 49, \
50, 51, 52, 53, 54, 55, 56, 57, }
-/* CPSW Ethernet support */
-#define CONFIG_BOOTP_DEFAULT
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_PHY_ATHEROS
-#define CONFIG_SYS_RX_ETH_BUFFER 64
-
-/* USB support */
-#define CONFIG_USB_XHCI_OMAP
-#define CONFIG_AM437X_USB2PHY2_HOST
-
-/* SPI Flash support */
-#define CONFIG_TI_SPI_MMAP
-
/* Power */
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
#define CONFIG_POWER_TPS65218
/* Enabling L2 Cache */
* Since SPL did pll and ddr initialization for us,
* we don't need to do it twice.
*/
-#if !defined(CONFIG_SPL_BUILD)
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#endif
#define CONFIG_HSMMC2_8BIT
#include <configs/ti_armv7_omap.h>
#undef CONFIG_SYS_MONITOR_LEN
-#define CONFIG_ENV_SIZE (16 * 1024)
-
#define V_OSCK 24000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK)
-#define CONFIG_ENV_SECT_SIZE (64 * 1024)
-#define CONFIG_ENV_OFFSET (768 * 1024)
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x80200000\0" \
"fdtaddr=0x81200000\0" \
"load mmc 1 ${fdtaddr} ${fdtfile} && " \
"bootz ${loadaddr} - ${fdtaddr}\0"
-#define CONFIG_BOOTCOMMAND \
- "mmc dev 0; " \
- "if mmc rescan; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "fi; " \
- "fi; " \
- "mmc dev 1; " \
- "if mmc rescan; then " \
- "run emmcboot; " \
- "fi;"
-
/* SPL defines. */
-#define CONFIG_SPL_TEXT_BASE 0x40300350
#define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + (128 << 20))
-#define CONFIG_SYS_SPI_U_BOOT_OFFS (256 * 1024)
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
/* EEPROM */
-#define CONFIG_ENV_EEPROM_IS_ON_I2C
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
-#define CONFIG_SYS_EEPROM_SIZE 256
#endif /* __CONFIG_CM_T43_H */