+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2011 CompuLab, Ltd.
* Mike Rapoport <mike@compulab.co.il>
* Syed Mohammed Khasim <x0khasim@ti.com>
*
* Configuration settings for the CompuLab CM-T35 and CM-T3730 boards
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
/*
* High Level Configuration Options
*/
-#define CONFIG_OMAP /* in a TI OMAP core */
-#define CONFIG_OMAP_GPIO
#define CONFIG_CM_T3X /* working with CM-T35 and CM-T3730 */
-#define CONFIG_OMAP_COMMON
-/* Common ARM Erratas */
-#define CONFIG_ARM_ERRATA_454179
-#define CONFIG_ARM_ERRATA_430973
-#define CONFIG_ARM_ERRATA_621766
-
-#define CONFIG_SDRC /* The chip has SDRC controller */
#include <asm/arch/cpu.h> /* get chip and board defs */
#include <asm/arch/omap.h>
-/*
- * Display CPU and Board information
- */
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DISPLAY_BOARDINFO
-
/* Clock Defines */
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
-#define CONFIG_MISC_INIT_R
-
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
/*
* select serial console configuration
*/
-#define CONFIG_CONS_INDEX 3
#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
-#define CONFIG_SERIAL3 3 /* UART3 */
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
115200}
-#define CONFIG_GENERIC_MMC
-#define CONFIG_MMC
-#define CONFIG_OMAP_HSMMC
-#define CONFIG_DOS_PARTITION
-
-/* USB */
-#define CONFIG_USB_OMAP3
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_OMAP
-#define CONFIG_USB_STORAGE
-#define CONFIG_USB_MUSB_UDC
-#define CONFIG_TWL4030_USB
-
/* USB device configuration */
#define CONFIG_USB_DEVICE
#define CONFIG_USB_TTY
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
/* commands to include */
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_EXT2 /* EXT2 Support */
-#define CONFIG_CMD_FAT /* FAT support */
-#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_MTD_PARTITIONS
-#define MTDIDS_DEFAULT "nand0=nand"
-#define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\
- "1920k(u-boot),256k(u-boot-env),"\
- "4m(kernel),-(fs)"
-
-#define CONFIG_CMD_MMC /* MMC support */
-#define CONFIG_CMD_NAND /* NAND support */
-
-#define CONFIG_SYS_NO_FLASH
+
#define CONFIG_SYS_I2C
-#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
-#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
-#define CONFIG_SYS_I2C_OMAP34XX
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_I2C_EEPROM_BUS 0
/*
* TWL4030
*/
-#define CONFIG_TWL4030_POWER
-#define CONFIG_TWL4030_LED
/*
* Board NAND Info.
*/
-#define CONFIG_NAND_OMAP_GPMC
-#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
- /* to access nand */
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
/* devices */
/* Environment information */
-#define CONFIG_BOOTDELAY 3
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x82000000\0" \
"usbtty=cdc_acm\0" \
"nand read ${loadaddr} 2a0000 400000; " \
"bootm ${loadaddr}\0" \
-#define CONFIG_CMD_BOOTZ
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
/*
* Miscellaneous configurable options
*/
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_CMDLINE_EDITING
#define CONFIG_TIMESTAMP
#define CONFIG_SYS_AUTOLOAD "no"
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) /* memtest */
/* works on */
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
-#define CONFIG_NR_DRAM_BANKS 1 /* CS1 is never populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
/*-----------------------------------------------------------------------
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
-#define CONFIG_ENV_IS_IN_NAND
-#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
-#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
-#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
-
-#if defined(CONFIG_CMD_NET)
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_32_BIT
-#define CM_T3X_SMC911X_BASE 0x2C000000
-#define SB_T35_SMC911X_BASE (CM_T3X_SMC911X_BASE + (16 << 20))
-#define CONFIG_SMC911X_BASE CM_T3X_SMC911X_BASE
-#endif /* (CONFIG_CMD_NET) */
+#define CONFIG_ENV_OFFSET 0x260000
+#define CONFIG_ENV_ADDR 0x260000
/* additions for new relocation code, must be added to all boards */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
GENERATED_GBL_DATA_SIZE)
/* Status LED */
-#define CONFIG_STATUS_LED /* Status LED enabled */
-#define CONFIG_BOARD_SPECIFIC_LED
-#define CONFIG_GPIO_LED
#define GREEN_LED_GPIO 186 /* CM-T35 Green LED is GPIO186 */
-#define GREEN_LED_DEV 0
-#define STATUS_LED_BIT GREEN_LED_GPIO
-#define STATUS_LED_STATE STATUS_LED_ON
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BOOT GREEN_LED_DEV
#define CONFIG_SPLASHIMAGE_GUARD
-/* GPIO banks */
-#ifdef CONFIG_STATUS_LED
-#define CONFIG_OMAP3_GPIO_6 /* GPIO186 is in GPIO bank 6 */
-#endif
-
/* Display Configuration */
-#define CONFIG_OMAP3_GPIO_2
-#define CONFIG_OMAP3_GPIO_5
-#define CONFIG_VIDEO_OMAP3
#define LCD_BPP LCD_COLOR16
-#define CONFIG_LCD
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SOURCE
-#define CONFIG_CMD_BMP
#define CONFIG_BMP_16BPP
#define CONFIG_SCF0403_LCD
-#define CONFIG_OMAP3_SPI
-
/* Defines for SPL */
-#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_NAND_SIMPLE
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
-#define CONFIG_SPL_BOARD_INIT
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBDISK_SUPPORT
-#define CONFIG_SPL_I2C_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_MMC_SUPPORT
-#define CONFIG_SPL_FAT_SUPPORT
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_ECC
-#define CONFIG_SPL_GPIO_SUPPORT
-#define CONFIG_SPL_POWER_SUPPORT
-#define CONFIG_SPL_OMAP3_ID_NAND
-#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
/* NAND boot config */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
-#define CONFIG_SPL_TEXT_BASE 0x40200800
-#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */
+#define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \
+ CONFIG_SPL_TEXT_BASE)
/*
* Use 0x80008000 as TEXT_BASE here for compatibility reasons with the
* older x-loader implementations. And move the BSS area so that it
* doesn't overlap with TEXT_BASE.
*/
-#define CONFIG_SYS_TEXT_BASE 0x80008000
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
+/* EEPROM */
+#define CONFIG_ENV_EEPROM_IS_ON_I2C
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+#define CONFIG_SYS_EEPROM_SIZE 256
+
#endif /* __CONFIG_H */