Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-staging

[platform/kernel/u-boot.git] / include / configs / cm_t335.h

diff --git a/include/configs/cm_t335.h b/include/configs/cm_t335.h
index e4eba02..767ef3a 100644 (file)
--- a/include/configs/cm_t335.h
+++ b/include/configs/cm_t335.h
@@ -107,6 +107,7 @@
 /* I2C Configuration */
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x50    /* Main EEPROM */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_BUS      0
 
 /* SPL */
 #define CONFIG_SPL_LDSCRIPT            "$(CPUDIR)/am33xx/u-boot-spl.lds"
@@ -114,7 +115,6 @@
 /* Network. */
 #define CONFIG_PHY_GIGE
 #define CONFIG_PHYLIB
-#define CONFIG_PHY_ADDR                        0
 #define CONFIG_PHY_ATHEROS
 
 /* NAND support */
@@ -142,7 +142,6 @@
 #define CONFIG_SYS_NAND_U_BOOT_OFFS    0x200000
 
 #define CONFIG_CMD_NAND
-#define GPMC_NAND_ECC_LP_x8_LAYOUT
 #define MTDIDS_DEFAULT                 "nand0=nand"
 #define MTDPARTS_DEFAULT               "mtdparts=nand:2m(spl)," \
                                        "1m(u-boot),1m(u-boot-env)," \
@@ -152,9 +151,36 @@
 #define CONFIG_ENV_OFFSET              0x300000 /* environment starts here */
 #define CONFIG_SYS_ENV_SECT_SIZE       (128 << 10)     /* 128 KiB */
 #define CONFIG_SYS_NAND_ONFI_DETECTION
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_CMD_SPL_NAND_OFS                0x400000 /* un-assigned: (using dtb) */
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS        0x500000
+#define CONFIG_CMD_SPL_WRITE_SIZE      0x2000
+#endif
 
 /* GPIO pin + bank to pin ID mapping */
 #define GPIO_PIN(_bank, _pin)          ((_bank << 5) + _pin)
 
+/* Status LED */
+#define CONFIG_STATUS_LED
+#define CONFIG_GPIO_LED
+#define CONFIG_BOARD_SPECIFIC_LED
+#define STATUS_LED_BIT                 GPIO_PIN(2, 0)
+/* Status LED polarity is inversed, so init it in the "off" state */
+#define STATUS_LED_STATE               STATUS_LED_OFF
+#define STATUS_LED_PERIOD              (CONFIG_SYS_HZ / 2)
+#define STATUS_LED_BOOT                        0
+
+#ifndef CONFIG_SPL_BUILD
+/*
+ * Enable PCA9555 at I2C0-0x26.
+ * First select the I2C0 bus with "i2c dev 0", then use "pca953x" command.
+ */
+#define CONFIG_PCA953X
+#define CONFIG_CMD_PCA953X
+#define CONFIG_CMD_PCA953X_INFO
+#define CONFIG_SYS_I2C_PCA953X_ADDR    0x26
+#define CONFIG_SYS_I2C_PCA953X_WIDTH   { {0x26, 16} }
+#endif /* CONFIG_SPL_BUILD */
+
 #endif /* __CONFIG_CM_T335_H */