+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Config file for Compulab CM-T335 board
*
* Copyright (C) 2013, Compulab Ltd - http://compulab.co.il/
*
* Author: Ilya Ledvich <ilya@compulab.co.il>
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_CM_T335_H
#define __CONFIG_CM_T335_H
-#define CONFIG_CM_T335
-#define CONFIG_NAND
-
#include <configs/ti_am335x_common.h>
-#undef CONFIG_SPI
-#undef CONFIG_OMAP3_SPI
-#undef CONFIG_BOOTCOUNT_LIMIT
-#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
-
#undef CONFIG_MAX_RAM_BANK_SIZE
#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* 512MB */
-#define CONFIG_MACH_TYPE MACH_TYPE_CM_T335
-
/* Clock Defines */
#define V_OSCK 25000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK)
-#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
-
#ifndef CONFIG_SPL_BUILD
#define MMCARGS \
"mmcdev=0\0" \
"bootm ${loadaddr}\0"
#define NANDARGS \
- "mtdids=" MTDIDS_DEFAULT "\0" \
- "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
+ "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
"nandroot=ubi0:rootfs rw\0" \
"nandrootfstype=ubifs\0" \
"nandargs=setenv bootargs console=${console} " \
#define CONFIG_SYS_AUTOLOAD "no"
/* Serial console configuration */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SERIAL1 1 /* UART0 */
/* NS16550 Configuration */
#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */
#define CONFIG_SYS_NS16550_COM2 0x48022000 /* UART1 */
/* I2C Configuration */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Main EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_I2C_EEPROM_BUS 0
/* SPL */
-#define CONFIG_SPL_LDSCRIPT "arch/arm/mach-omap2/u-boot-spl.lds"
/* Network. */
-#define CONFIG_PHY_ATHEROS
/* NAND support */
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
- CONFIG_SYS_NAND_PAGE_SIZE)
-#define CONFIG_SYS_NAND_PAGE_SIZE 2048
-#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
10, 11, 12, 13, 14, 15, 16, 17, \
18, 19, 20, 21, 22, 23, 24, 25, \
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-#undef CONFIG_SYS_NAND_U_BOOT_OFFS
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x200000
-
-#define MTDIDS_DEFAULT "nand0=nand"
-#define MTDPARTS_DEFAULT "mtdparts=nand:2m(spl)," \
- "1m(u-boot),1m(u-boot-env)," \
- "1m(dtb),4m(splash)," \
- "6m(kernel),-(rootfs)"
-#define CONFIG_ENV_OFFSET 0x300000 /* environment starts here */
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
-#define CONFIG_SYS_NAND_ONFI_DETECTION
#ifdef CONFIG_SPL_OS_BOOT
#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x500000
-#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
#endif
/* GPIO pin + bank to pin ID mapping */
/* Status LED polarity is inversed, so init it in the "off" state */
/* EEPROM */
-#define CONFIG_ENV_EEPROM_IS_ON_I2C
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
-#define CONFIG_SYS_EEPROM_SIZE 256
#ifndef CONFIG_SPL_BUILD
/*
#endif /* CONFIG_SPL_BUILD */
#endif /* __CONFIG_CM_T335_H */
-