+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Config file for Compulab CM-T335 board
*
* Copyright (C) 2013, Compulab Ltd - http://compulab.co.il/
*
* Author: Ilya Ledvich <ilya@compulab.co.il>
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_CM_T335_H
#define __CONFIG_CM_T335_H
#define CONFIG_CM_T335
-#define CONFIG_NAND
#include <configs/ti_am335x_common.h>
-#undef CONFIG_BOARD_LATE_INIT
-#undef CONFIG_SPI
-#undef CONFIG_OMAP3_SPI
-#undef CONFIG_BOOTCOUNT_LIMIT
-#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
-
#undef CONFIG_MAX_RAM_BANK_SIZE
#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* 512MB */
-#define CONFIG_OMAP_COMMON
-
-#define MACH_TYPE_CM_T335 4586 /* Until the next sync */
#define CONFIG_MACH_TYPE MACH_TYPE_CM_T335
/* Clock Defines */
#define V_OSCK 25000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK)
-#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
-
#ifndef CONFIG_SPL_BUILD
#define MMCARGS \
"mmcdev=0\0" \
"bootm ${loadaddr}\0"
#define NANDARGS \
- "mtdids=" MTDIDS_DEFAULT "\0" \
- "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
+ "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
"nandroot=ubi0:rootfs rw\0" \
"nandrootfstype=ubifs\0" \
"nandargs=setenv bootargs console=${console} " \
#define CONFIG_SYS_AUTOLOAD "no"
/* Serial console configuration */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SERIAL1 1 /* UART0 */
/* NS16550 Configuration */
#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */
#define CONFIG_SYS_NS16550_COM2 0x48022000 /* UART1 */
-#define CONFIG_BAUDRATE 115200
/* I2C Configuration */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Main EEPROM */
#define CONFIG_SYS_I2C_EEPROM_BUS 0
/* SPL */
-#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds"
/* Network. */
-#define CONFIG_PHY_GIGE
-#define CONFIG_PHYLIB
-#define CONFIG_PHY_ATHEROS
/* NAND support */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#undef CONFIG_SYS_NAND_U_BOOT_OFFS
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x200000
-#define CONFIG_CMD_NAND
-#define MTDIDS_DEFAULT "nand0=nand"
-#define MTDPARTS_DEFAULT "mtdparts=nand:2m(spl)," \
- "1m(u-boot),1m(u-boot-env)," \
- "1m(dtb),4m(splash)," \
- "6m(kernel),-(rootfs)"
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_OFFSET 0x300000 /* environment starts here */
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
#define CONFIG_SYS_NAND_ONFI_DETECTION
#ifdef CONFIG_SPL_OS_BOOT
-#define CONFIG_CMD_SPL_NAND_OFS 0x400000 /* un-assigned: (using dtb) */
#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x500000
-#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
#endif
/* GPIO pin + bank to pin ID mapping */
#define GPIO_PIN(_bank, _pin) ((_bank << 5) + _pin)
/* Status LED */
-#define CONFIG_STATUS_LED
-#define CONFIG_GPIO_LED
-#define CONFIG_BOARD_SPECIFIC_LED
-#define STATUS_LED_BIT GPIO_PIN(2, 0)
/* Status LED polarity is inversed, so init it in the "off" state */
-#define STATUS_LED_STATE STATUS_LED_OFF
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BOOT 0
/* EEPROM */
-#define CONFIG_CMD_EEPROM
#define CONFIG_ENV_EEPROM_IS_ON_I2C
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
#define CONFIG_SYS_EEPROM_SIZE 256
-#define CONFIG_CMD_EEPROM_LAYOUT
-#define CONFIG_EEPROM_LAYOUT_HELP_STRING "v2, v3"
-
#ifndef CONFIG_SPL_BUILD
/*
* Enable PCA9555 at I2C0-0x26.
* First select the I2C0 bus with "i2c dev 0", then use "pca953x" command.
*/
#define CONFIG_PCA953X
-#define CONFIG_CMD_PCA953X
-#define CONFIG_CMD_PCA953X_INFO
#define CONFIG_SYS_I2C_PCA953X_ADDR 0x26
#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x26, 16} }
#endif /* CONFIG_SPL_BUILD */