+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Config file for Compulab CM-FX6 board
*
* Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
*
* Author: Nikita Kiryanov <nikita@compulab.co.il>
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_CM_FX6_H
#define CONFIG_SYS_LITTLE_ENDIAN
#define CONFIG_MACH_TYPE 4273
-/* CMD */
-#define CONFIG_CMD_MTDPARTS
-
/* MMC */
#define CONFIG_SYS_FSL_USDHC_NUM 3
#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR
#define PHYS_SDRAM_1 MMDC0_ARB_BASE_ADDR
#define PHYS_SDRAM_2 MMDC1_ARB_BASE_ADDR
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_NR_DRAM_BANKS 2
#define CONFIG_SYS_MEMTEST_START 0x10000000
#define CONFIG_SYS_MEMTEST_END 0x10010000
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
/* Serial console */
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE UART4_BASE
-#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
-/* Shell */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-
/* SPI flash */
-#define CONFIG_SF_DEFAULT_BUS 0
-#define CONFIG_SF_DEFAULT_CS 0
-#define CONFIG_SF_DEFAULT_SPEED 25000000
-#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
/* MTD support */
#ifndef CONFIG_SPL_BUILD
-#define CONFIG_MTD_DEVICE
-#define CONFIG_MTD_PARTITIONS
#define CONFIG_SPI_FLASH_MTD
#endif
-#define MTDIDS_DEFAULT "nor0=spi0.0"
-#define MTDPARTS_DEFAULT "mtdparts=spi0.0:" \
- "768k(uboot)," \
- "256k(uboot-environment)," \
- "-(reserved)"
-
/* Environment */
-#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SIZE (8 * 1024)
#define CONFIG_ENV_OFFSET (768 * 1024)
+#ifndef CONFIG_SPL_BUILD
#define CONFIG_EXTRA_ENV_SETTINGS \
+ "fdt_high=0xffffffff\0" \
+ "initrd_high=0xffffffff\0" \
+ "fdt_addr_r=0x18000000\0" \
+ "ramdisk_addr_r=0x13000000\0" \
+ "kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
+ "pxefile_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
+ "scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
+ "fdtfile=undefined\0" \
"stdin=serial,usbkbd\0" \
"stdout=serial,vga\0" \
"stderr=serial,vga\0" \
"uImage=uImage-cm-fx6\0" \
"zImage=zImage-cm-fx6\0" \
"kernel=uImage-cm-fx6\0" \
- "script=boot.scr\0" \
"dtb=cm-fx6.dtb\0" \
- "bootm_low=18000000\0" \
- "loadaddr=0x10800000\0" \
- "fdtaddr=0x11000000\0" \
"console=ttymxc3,115200\0" \
"ethprime=FEC0\0" \
"video_hdmi=mxcfb0:dev=hdmi,1920x1080M-32@50,if=RGB32\0" \
"video_dvi=mxcfb0:dev=dvi,1280x800M-32@50,if=RGB32\0" \
- "doboot=bootm ${loadaddr}\0" \
+ "doboot=bootm ${kernel_addr_r}\0" \
"doloadfdt=false\0" \
- "mtdids=" MTDIDS_DEFAULT "\0" \
- "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
+ "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
"setboottypez=setenv kernel ${zImage};" \
- "setenv doboot bootz ${loadaddr} - ${fdtaddr};" \
+ "setenv doboot bootz ${kernel_addr_r} - ${fdt_addr_r};" \
"setenv doloadfdt true;\0" \
"setboottypem=setenv kernel ${uImage};" \
- "setenv doboot bootm ${loadaddr};" \
+ "setenv doboot bootm ${kernel_addr_r};" \
"setenv doloadfdt false;\0"\
"mmcroot=/dev/mmcblk0p2 rw rootwait\0" \
"sataroot=/dev/sda2 rw rootwait\0" \
"run_eboot=echo Starting EBOOT ...; "\
"mmc dev 2 && " \
"mmc rescan && mmc read 10042000 a 400 && go 10042000\0" \
- "loadscript=load ${storagetype} ${storagedev} ${loadaddr} ${script};\0"\
- "loadkernel=load ${storagetype} ${storagedev} ${loadaddr} ${kernel};\0"\
- "loadfdt=load ${storagetype} ${storagedev} ${fdtaddr} ${dtb};\0" \
- "bootscript=echo Running bootscript from ${storagetype} ...;" \
- "source ${loadaddr};\0" \
- "nandloadkernel=nand read ${loadaddr} 0 780000;\0" \
- "nandloadfdt=nand read ${fdtaddr} 780000 80000;\0" \
+ "loadkernel=load ${storagetype} ${storagedev} ${kernel_addr_r} ${kernel};\0"\
+ "loadfdt=load ${storagetype} ${storagedev} ${fdt_addr_r} ${dtb};\0" \
+ "nandloadkernel=nand read ${kernel_addr_r} 0 780000;\0" \
+ "nandloadfdt=nand read ${fdt_addr_r} 780000 80000;\0" \
"setupmmcboot=setenv storagetype mmc; setenv storagedev 2;\0" \
"setupsataboot=setenv storagetype sata; setenv storagedev 0;\0" \
"setupnandboot=setenv storagetype nand;\0" \
- "setupusbboot=setenv storagetype usb; setenv storagedev 0;\0" \
"storagebootcmd=echo Booting from ${storagetype} ...;" \
"run ${storagetype}args; run doboot;\0" \
"trybootk=if run loadkernel; then " \
"fi;" \
"run storagebootcmd;" \
"fi;\0" \
- "trybootsmz=if run loadscript; then " \
- "run bootscript;" \
- "fi;" \
+ "trybootsmz=" \
"run setboottypem;" \
"run trybootk;" \
"run setboottypez;" \
- "run trybootk;\0"
-
-#define CONFIG_BOOTCOMMAND \
- "run setupmmcboot;" \
- "mmc dev ${storagedev};" \
- "if mmc rescan; then " \
- "run trybootsmz;" \
- "fi;" \
- "run setupusbboot;" \
- "if usb start; then "\
- "if run loadscript; then " \
- "run bootscript;" \
+ "run trybootk;\0" \
+ "legacy_bootcmd=" \
+ "run setupmmcboot;" \
+ "mmc dev ${storagedev};" \
+ "if mmc rescan; then " \
+ "run trybootsmz;" \
+ "fi;" \
+ "run setupsataboot;" \
+ "if sata init; then " \
+ "run trybootsmz;" \
"fi;" \
- "fi;" \
- "run setupsataboot;" \
- "if sata init; then " \
- "run trybootsmz;" \
- "fi;" \
- "run setupnandboot;" \
- "run nandboot;"
+ "run setupnandboot;" \
+ "run nandboot;\0" \
+ "findfdt="\
+ "if test $board_name = Utilite && test $board_rev = MX6Q ; then " \
+ "setenv fdtfile imx6q-utilite-pro.dtb; fi; " \
+ "if test $fdtfile = undefined; then " \
+ "echo WARNING: Could not determine dtb to use; fi; \0" \
+ BOOTENV
#define CONFIG_PREBOOT "usb start;sf probe"
-/* SPI */
-#define CONFIG_SPI
-#define CONFIG_MXC_SPI
+#define BOOT_TARGET_DEVICES(func) \
+ func(USB, usb, 0) \
+ func(MMC, mmc, 2) \
+ func(SATA, sata, 0)
+
+#include <config_distro_bootcmd.h>
+#else
+#define CONFIG_EXTRA_ENV_SETTINGS
+#endif
/* NAND */
#ifndef CONFIG_SPL_BUILD
-#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BASE 0x40000000
#define CONFIG_SYS_NAND_MAX_CHIPS 1
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_NAND_MXS
#define CONFIG_SYS_NAND_ONFI_DETECTION
/* APBH DMA is required for NAND support */
-#define CONFIG_APBH_DMA
-#define CONFIG_APBH_DMA_BURST
-#define CONFIG_APBH_DMA_BURST8
#endif
/* Ethernet */
#define CONFIG_FEC_MXC_PHYADDR 0
#define CONFIG_FEC_XCV_TYPE RGMII
#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_PHYLIB
#define CONFIG_PHY_ATHEROS
-#define CONFIG_MII
#define CONFIG_ETHPRIME "FEC0"
#define CONFIG_ARP_TIMEOUT 200UL
#define CONFIG_NET_RETRY_COUNT 5
#define CONFIG_SYS_I2C_EEPROM_BUS 2
/* SATA */
-#define CONFIG_CMD_SATA
#define CONFIG_SYS_SATA_MAX_DEVICE 1
-#define CONFIG_LIBATA
#define CONFIG_LBA48
-#define CONFIG_DWC_AHSATA
#define CONFIG_DWC_AHSATA_PORT_ID 0
#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
#define CONFIG_SERIAL_TAG
/* misc */
-#define CONFIG_STACKSIZE (128 * 1024)
#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 800 /* 400 KB */
-#define CONFIG_MISC_INIT_R
/* SPL */
#include "imx6_spl.h"
#define CONFIG_SYS_SPI_U_BOOT_OFFS (64 * 1024)
-#define CONFIG_SPL_SPI_LOAD
/* Display */
#define CONFIG_VIDEO_IPUV3
-#define CONFIG_IPUV3_CLK 260000000
#define CONFIG_IMX_HDMI
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SOURCE
-#define CONFIG_CMD_BMP
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
/* EEPROM */
-#define CONFIG_CMD_EEPROM
#define CONFIG_ENV_EEPROM_IS_ON_I2C
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
#define CONFIG_SYS_EEPROM_SIZE 256
-#define CONFIG_CMD_EEPROM_LAYOUT
-#define CONFIG_EEPROM_LAYOUT_HELP_STRING "v2, v3"
-
#endif /* __CONFIG_CM_FX6_H */