powerpc, 8xx: remove support for 8xx

[platform/kernel/u-boot.git] / include / configs / cm5200.h

diff --git a/include/configs/cm5200.h b/include/configs/cm5200.h
index 69b2674..3777a0d 100644 (file)
--- a/include/configs/cm5200.h
+++ b/include/configs/cm5200.h
@@ -8,10 +8,6 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-
-#define CONFIG_DISPLAY_BOARDINFO
-
-
 /*
  * High Level Configuration Options
  */
@@ -25,27 +21,13 @@
 /*
  * Supported commands
  */
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BSP
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SNTP
-#define CONFIG_CMD_USB
 
 /*
  * Serial console configuration
  */
 #define CONFIG_PSC_CONSOLE     1       /* console is on PSC1 */
-#define CONFIG_BAUDRATE                57600   /* ... at 57600 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200, 230400 }
-#define CONFIG_SILENT_CONSOLE  1       /* needed to silence i2c_init() */
 
 /*
  * Ethernet configuration
@@ -61,7 +43,7 @@
 /*
  * POST support
  */
-#define CONFIG_POST            (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU | CONFIG_SYS_POST_I2C)
+#define CONFIG_POST            (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU)
 #define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4)
 /* List of I2C addresses to be verified by POST */
 #define CONFIG_SYS_POST_I2C_ADDRS      {CONFIG_SYS_I2C_SLAVE,  \
@@ -74,7 +56,6 @@
 /*
  * Autobooting
  */
-#define CONFIG_BOOTDELAY       5       /* autoboot after 5 seconds */
 #define CONFIG_PREBOOT "echo;" \
        "echo Type \"run net_nfs_fdt\" to mount root filesystem over NFS;" \
        "echo"
@@ -172,13 +153,11 @@
 #define CONFIG_SYS_MAX_FLASH_SECT      256     /* max num of sectors on one chip */
 #define CONFIG_SYS_FLASH_SIZE          0x02000000 /* 32 MiB */
 
-
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #define CONFIG_SYS_RAMBOOT             1
 #undef CONFIG_SYS_LOWBOOT
 #endif
 
-
 /*
  * Chip selects configuration
  */
@@ -220,16 +199,6 @@
                                        "-(config)"
 
 /*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C                1       /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE          2       /* Select I2C module #2 */
-#define CONFIG_SYS_I2C_SPEED           40000   /* 40 kHz */
-#define CONFIG_SYS_I2C_SLAVE           0x0
-#define CONFIG_SYS_I2C_IO              0x38    /* PCA9554AD I2C I/O port address */
-#define CONFIG_SYS_I2C_EEPROM          0x53    /* I2C EEPROM device address */
-
-/*
  * RTC configuration
  */
 #define CONFIG_RTC_MPC5200     1       /* use internal MPC5200 RTC */
@@ -238,13 +207,9 @@
  * USB configuration
  */
 #define CONFIG_USB_OHCI                1
-#define CONFIG_USB_STORAGE     1
 #define CONFIG_USB_CLOCK       0x0001BBBB
 #define CONFIG_USB_CONFIG      0x00001000
 /* Partitions (for USB) */
-#define CONFIG_MAC_PARTITION   1
-#define CONFIG_DOS_PARTITION   1
-#define CONFIG_ISO_PARTITION   1
 
 /*
  * Invoke our last_stage_init function - needed by fwupdate
@@ -292,8 +257,6 @@
 #define CONFIG_SYS_MEMTEST_START       0x00100000      /* memtest works on */
 #define CONFIG_SYS_MEMTEST_END         0x03f00000      /* 1 .. 63 MiB in SDRAM */
 
-#define CONFIG_LOOPW           1
-
 #define CONFIG_SYS_LOAD_ADDR           0x100000        /* default load address */
 
 /*
@@ -315,8 +278,6 @@
 /*
  * Flat Device Tree support
  */
-#define CONFIG_OF_LIBFDT       1
-#define CONFIG_OF_BOARD_SETUP  1
 #define OF_CPU                 "PowerPC,5200@0"
 #define OF_SOC                 "soc5200@f0000000"
 #define OF_TBCLK               (bd->bi_busfreq / 4)