#ifndef _CONFIG_CLEARFOG_H
#define _CONFIG_CLEARFOG_H
+#include <linux/stringify.h>
+
/*
* High Level Configuration Options (easy to change)
*/
#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
/*
- * Commands configuration
- */
-
-/*
* SDIO/MMC Card Configuration
*/
#define CONFIG_SYS_MMC_BASE MVEBU_SDIO_BASE
#define CONFIG_ENV_MIN_ENTRIES 128
/* Environment in MMC */
-#define CONFIG_SYS_MMC_ENV_DEV 0
/*
* For SD - reserve 1 LBA for MBR + 1M for u-boot image. The MMC/eMMC
* boot image starts @ LBA-0.
#define BOOT_TARGET_DEVICES_MMC(func)
#endif
-#ifdef CONFIG_SCSI
-#define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0)
-#else
-#define BOOT_TARGET_DEVICES_SCSI(func)
-#endif
-
#ifdef CONFIG_USB_STORAGE
#define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
#else
#define BOOT_TARGET_DEVICES_USB(func)
#endif
-#ifdef CONFIG_SCSI
-#define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0)
+#ifndef CONFIG_SCSI
+#define BOOT_TARGET_DEVICES_SCSI_BUS0(func)
+#define BOOT_TARGET_DEVICES_SCSI_BUS1(func)
+#define BOOT_TARGET_DEVICES_SCSI_BUS2(func)
#else
-#define BOOT_TARGET_DEVICES_SCSI(func)
+/*
+ * With SCSI enabled, M.2 SATA is always located on bus 0
+ */
+#define BOOT_TARGET_DEVICES_SCSI_BUS0(func) func(SCSI, scsi, 0)
+
+/*
+ * Either one or both mPCIe slots may be configured as mSATA interfaces. The
+ * SCSI bus ids are assigned based on sequence of hardware present, not always
+ * tied to hardware slot ids. As such, use second SCSI bus if either slot is
+ * set for SATA, and only use third SCSI bus if both slots are SATA enabled.
+ */
+#if defined (CONFIG_CLEARFOG_CON2_SATA) || defined (CONFIG_CLEARFOG_CON3_SATA)
+#define BOOT_TARGET_DEVICES_SCSI_BUS1(func) func(SCSI, scsi, 1)
+#else
+#define BOOT_TARGET_DEVICES_SCSI_BUS1(func)
+#endif
+
+#if defined (CONFIG_CLEARFOG_CON2_SATA) && defined (CONFIG_CLEARFOG_CON3_SATA)
+#define BOOT_TARGET_DEVICES_SCSI_BUS2(func) func(SCSI, scsi, 2)
+#else
+#define BOOT_TARGET_DEVICES_SCSI_BUS2(func)
#endif
+#endif /* CONFIG_SCSI */
+
+/*
+ * The SCSI buses are attempted in increasing bus order, there is no current
+ * mechanism to alter the default bus priority order for booting.
+ */
#define BOOT_TARGET_DEVICES(func) \
BOOT_TARGET_DEVICES_MMC(func) \
- BOOT_TARGET_DEVICES_SCSI(func) \
BOOT_TARGET_DEVICES_USB(func) \
- BOOT_TARGET_DEVICES_SCSI(func) \
+ BOOT_TARGET_DEVICES_SCSI_BUS0(func) \
+ BOOT_TARGET_DEVICES_SCSI_BUS1(func) \
+ BOOT_TARGET_DEVICES_SCSI_BUS2(func) \
func(PXE, pxe, na) \
func(DHCP, dhcp, na)
#define CONFIG_EXTRA_ENV_SETTINGS \
RELOCATION_LIMITS_ENV_SETTINGS \
LOAD_ADDRESS_ENV_SETTINGS \
- "fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
"console=ttyS0,115200\0" \
BOOTENV