/*-----------------------------------------------------------------------
* High Level Configuration Options
*----------------------------------------------------------------------*/
-#define CONFIG_CANYONLANDS 1 /* Board is Canyonlands */
+/* This config file is used for Canyonlands (460EX) and Glacier (460GT) */
+#ifndef CONFIG_CANYONLANDS
+#define CONFIG_460GT 1 /* Specific PPC460GT */
+#define CONFIG_HOSTNAME glacier
+#else
+#define CONFIG_460EX 1 /* Specific PPC460EX */
+#define CONFIG_HOSTNAME canyonlands
+#endif
#define CONFIG_440 1
#define CONFIG_4xx 1 /* ... PPC4xx family */
-#define CONFIG_460EX 1 /* Specific PPC460EX support */
+
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#include "amcc-common.h"
#define CONFIG_SYS_CLK_FREQ 66666667 /* external freq to pll */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_BOARD_EARLY_INIT_R 1 /* Call board_early_init_r */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
+#define CONFIG_BOARD_TYPES 1 /* support board types */
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-
#define CFG_PCI_MEMBASE 0x80000000 /* mapped PCI memory */
#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */
#define CFG_PCI_TARGBASE CFG_PCI_MEMBASE
#define CFG_AHB_BASE 0xE2000000 /* internal AHB peripherals */
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc()*/
-
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in OCM)
*----------------------------------------------------------------------*/
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
#undef CONFIG_UART1_CONSOLE /* define this if you want console on UART1 */
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
* Define here the location of the environment variables (FLASH).
*/
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
-#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
#define CFG_NAND_CS 3 /* NAND chip connected to CSx */
#else
-#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
+#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
#define CFG_NAND_CS 0 /* NAND chip connected to CSx */
-#define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */
+#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */
#endif
/*
* On 440EPx the SPL is copied to SDRAM before the NAND controller is
* set up. While still running from cache, I experienced problems accessing
* the NAND controller. sr - 2006-08-25
+ *
+ * This is the first official implementation of booting from 2k page sized
+ * NAND devices (e.g. Micron 29F2G08AA 256Mbit * 8)
*/
#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
/*
* Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
*/
-#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
-#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
+#define CFG_NAND_U_BOOT_OFFS (128 << 10) /* Offset to RAM U-Boot image */
+#define CFG_NAND_U_BOOT_SIZE (1 << 20) /* Size of RAM U-Boot image */
/*
* Now the NAND chip has to be defined (no autodetection used!)
*/
-#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */
-#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
-#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */
-#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
-#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */
+#define CFG_NAND_PAGE_SIZE (2 << 10) /* NAND chip page size */
+#define CFG_NAND_BLOCK_SIZE (128 << 10) /* NAND chip block size */
+#define CFG_NAND_PAGE_COUNT (CFG_NAND_BLOCK_SIZE / CFG_NAND_PAGE_SIZE)
+ /* NAND chip page count */
+#define CFG_NAND_BAD_BLOCK_POS 0 /* Location of bad block marker*/
+#define CFG_NAND_5_ADDR_CYCLE /* Fifth addr used (<=128MB) */
#define CFG_NAND_ECCSIZE 256
#define CFG_NAND_ECCBYTES 3
#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE)
-#define CFG_NAND_OOBSIZE 16
+#define CFG_NAND_OOBSIZE 64
#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS)
-#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
+#define CFG_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47, \
+ 48, 49, 50, 51, 52, 53, 54, 55, \
+ 56, 57, 58, 59, 60, 61, 62, 63}
-#ifdef CFG_ENV_IS_IN_NAND
+#ifdef CONFIG_ENV_IS_IN_NAND
/*
* For NAND booting the environment is embedded in the U-Boot image. Please take
* look at the file board/amcc/canyonlands/u-boot-nand.lds for details.
*/
-#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE
-#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE)
-#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE)
+#define CONFIG_ENV_SIZE CFG_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#endif
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
#define CFG_FLASH_CFI /* The flash is CFI compatible */
-#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CFG_FLASH_CFI_AMD_RESET 1 /* Use AMD (Spansion) reset cmd */
#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR - CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
-#endif /* CFG_ENV_IS_IN_FLASH */
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+#endif /* CONFIG_ENV_IS_IN_FLASH */
/*-----------------------------------------------------------------------
* NAND-FLASH related
#define CONFIG_DDR_ECC 1 /* with ECC support */
#define CONFIG_DDR_RQDC_FIXED 0x80000038 /* fixed value for RQDC */
#endif
-#define CFG_MBYTES_SDRAM 256 /* 256MB */
+#define CFG_MBYTES_SDRAM 512 /* 512MB */
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_SPEED 400000 /* I2C speed */
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
#define CFG_EEPROM_PAGE_WRITE_BITS 3
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
* Ethernet
*----------------------------------------------------------------------*/
#define CONFIG_IBM_EMAC4_V4 1
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
#define CONFIG_PHY1_ADDR 1
-#define CONFIG_HAS_ETH0 1
-#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
-#define CONFIG_NET_MULTI 1
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+/* Only Glacier (460GT) has 4 EMAC interfaces */
+#ifdef CONFIG_460GT
+#define CONFIG_PHY2_ADDR 2
+#define CONFIG_PHY3_ADDR 3
+#define CONFIG_HAS_ETH2
+#define CONFIG_HAS_ETH3
+#endif
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_PHY_DYNAMIC_ANEG 1
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
/*-----------------------------------------------------------------------
* USB-OHCI
*----------------------------------------------------------------------*/
+/* Only Canyonlands (460EX) has USB */
+#ifdef CONFIG_460EX
#define CONFIG_USB_OHCI_NEW
#define CONFIG_USB_STORAGE
#undef CFG_OHCI_BE_CONTROLLER /* 460EX has little endian descriptors */
#define CFG_USB_OHCI_REGS_BASE (CFG_AHB_BASE | 0xd0000)
#define CFG_USB_OHCI_SLOT_NAME "ppc440"
#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
+#endif
-/*-----------------------------------------------------------------------
- * Default environment
- *----------------------------------------------------------------------*/
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=canyonlands\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "net_nfs=tftp 200000 ${bootfile};" \
- "run nfsargs addip addtty;" \
- "bootm 200000\0" \
- "net_nfs_fdt=tftp 200000 ${bootfile};" \
- "tftp ${fdt_addr} ${fdt_file};" \
- "run nfsargs addip addtty;" \
- "bootm 200000 - ${fdt_addr}\0" \
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "rootpath=/opt/eldk/ppc_4xxFP\0" \
- "bootfile=canyonlands/uImage\0" \
- "fdt_file=canyonlands/canyonlands.dtb\0" \
- "fdt_addr=400000\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ CONFIG_AMCC_DEF_ENV_NAND_UPD \
"kernel_addr=fc000000\0" \
+ "fdt_addr=fc1e0000\0" \
"ramdisk_addr=fc200000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 200000 canyonlands/u-boot.bin\0" \
- "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \
- "cp.b ${fileaddr} fffa0000 ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
- "nload=tftp 200000 canyonlands/u-boot-nand.bin\0" \
- "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \
- "setenv filesize;saveenv\0" \
- "nupd=run nload nupdate\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:RP\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_SNTP
+#ifdef CONFIG_460EX
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
#define CONFIG_CMD_USB
+#endif
/* Partitions */
#define CONFIG_MAC_PARTITION
#define CONFIG_ISO_PARTITION
/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-
-#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
-#endif
-
-/*-----------------------------------------------------------------------
* PCI stuff
*----------------------------------------------------------------------*/
/* General PCI */
#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
/*
* PPC4xx GPIO Configuration
*/
+#ifdef CONFIG_460EX
+/* 460EX: Use USB configuration */
#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
{ \
/* GPIO Core 0 */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \
} \
}
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
+#else
+/* 460GT: Use EMAC2+3 configuration */
+#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
+{ \
+/* GPIO Core 0 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 GMC1TxD(0) USB2HostD(0) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 GMC1TxD(1) USB2HostD(1) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 GMC1TxD(2) USB2HostD(2) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO3 GMC1TxD(3) USB2HostD(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO4 GMC1TxD(4) USB2HostD(4) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO5 GMC1TxD(5) USB2HostD(5) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 GMC1TxD(6) USB2HostD(6) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 GMC1TxD(7) USB2HostD(7) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 GMC1RxD(0) USB2OTGD(0) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 GMC1RxD(1) USB2OTGD(1) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 GMC1RxD(2) USB2OTGD(2) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 GMC1RxD(3) USB2OTGD(3) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO12 GMC1RxD(4) USB2OTGD(4) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO13 GMC1RxD(5) USB2OTGD(5) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO14 GMC1RxD(6) USB2OTGD(6) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO15 GMC1RxD(7) USB2OTGD(7) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 GMC1TxER USB2HostStop */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 GMC1CD USB2HostNext */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 GMC1RxER USB2HostDir */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 GMC1TxEN USB2OTGStop */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 GMC1CRS USB2OTGNext */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 GMC1RxDV USB2OTGDir */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO22 NFRDY */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 NFREN */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO24 NFWEN */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO25 NFCLE */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 NFALE */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO27 IRQ(0) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO28 IRQ(1) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO29 IRQ(2) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO30 PerPar0 DMAReq2 IRQ(7)*/ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO31 PerPar1 DMAAck2 IRQ(8)*/ \
+}, \
+{ \
+/* GPIO Core 1 */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO32 PerPar2 EOT2/TC2 IRQ(9)*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO33 PerPar3 DMAReq3 IRQ(4)*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT3, GPIO_OUT_1}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N DMAAck3 UART3_SIN*/ \
+{GPIO1_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO37 UART0_RTS_N EOT3/TC3 UART3_SOUT*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 IRQ(3) */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 CS(1) */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 CS(2) */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 CS(3) DMAReq1 IRQ(10)*/ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO44 CS(4) DMAAck1 IRQ(11)*/ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO45 CS(5) EOT/TC1 IRQ(12)*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO46 PerAddr(5) DMAReq0 IRQ(13)*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO47 PerAddr(6) DMAAck0 IRQ(14)*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO48 PerAddr(7) EOT/TC0 IRQ(15)*/ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO49 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO53 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO54 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO55 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO57 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \
+} \
+}
+#endif
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff