#define CONFIG_SYS_PCIE0_XCFGBASE 0xc3000000
#define CONFIG_SYS_PCIE1_XCFGBASE 0xc3001000
+/*
+ * BCSR bits as defined in the Canyonlands board user manual.
+ */
+#define BCSR_USBCTRL_OTG_RST 0x32
+#define BCSR_USBCTRL_HOST_RST 0x01
+#define BCSR_SELECT_PCIE 0x10
+
#define CONFIG_SYS_PCIE0_UTLBASE 0xc08010000ULL /* 36bit physical addr */
/* base address of inbound PCIe window */
*/
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#define CONFIG_SYS_NOR_CS 0 /* NOR chip connected to CSx */
#define CONFIG_SYS_NAND_CS 3 /* NAND chip connected to CSx */
#else
#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
+#define CONFIG_SYS_NOR_CS 3 /* NOR chip connected to CSx */
#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */
#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */
#endif
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
+/* I2C bootstrap EEPROM */
+#if defined(CONFIG_ARCHES)
+#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x54
+#else
+#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x52
+#endif
+#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0
+#define CONFIG_4xx_CONFIG_BLOCKSIZE 16
+
/* I2C SYSMON (LM75, AD7414 is almost compatible) */
#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
#define CONFIG_DTT_AD7414 1 /* use AD7414 */
#define CONFIG_SYS_USB_OHCI_REGS_BASE (CONFIG_SYS_AHB_BASE | 0xd0000)
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
+#define CONFIG_SYS_USB_OHCI_BOARD_INIT
#endif
/*
/*
* Commands additional to the ones defined in amcc-common.h
*/
+#define CONFIG_CMD_CHIP_CONFIG
#if defined(CONFIG_ARCHES)
#define CONFIG_CMD_DTT
#define CONFIG_CMD_PCI
#define CONFIG_CMD_FAT
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PCI
+#define CONFIG_CMD_SATA
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SNTP
#define CONFIG_CMD_USB
#endif /* CONFIG_ARCHES */
#endif /* CONFIG_460GT */
+/*
+ * SATA driver setup
+ */
+#ifdef CONFIG_CMD_SATA
+#define CONFIG_SATA_DWC
+#define CONFIG_LIBATA
+#define SATA_BASE_ADDR 0xe20d1000 /* PPC460EX SATA Base Address */
+#define SATA_DMA_REG_ADDR 0xe20d0800 /* PPC460EX SATA Base Address */
+#define CONFIG_SYS_SATA_MAX_DEVICE 1 /* SATA MAX DEVICE */
+/* Convert sectorsize to wordsize */
+#define ATA_SECTOR_WORDS (ATA_SECT_SIZE/2)
+#endif
+
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_FPGA_BASE | 0x3a000) /* BAS=FPGA,BS=2MB,BU=R/W,BW=16bit*/
#endif /* !defined(CONFIG_ARCHES) */
-#define CONFIG_SYS_EBC_CFG 0xB8400000 /* EBC0_CFG */
+#define CONFIG_SYS_EBC_CFG 0xbfc00000
/*
* Arches doesn't use PerCS3 but GPIO43, so let's configure the GPIO