common: add CMD_GPIO to Kconfig

[platform/kernel/u-boot.git] / include / configs / bur_am335x_common.h

diff --git a/include/configs/bur_am335x_common.h b/include/configs/bur_am335x_common.h
index 639e5a0..c9eb63e 100644 (file)
--- a/include/configs/bur_am335x_common.h
+++ b/include/configs/bur_am335x_common.h
@@ -14,25 +14,18 @@
 /* ------------------------------------------------------------------------- */
 #define BUR_COMMON_ENV \
 "usbscript=usb start && fatload usb 0 0x80000000 usbscript.img && source\0" \
-"defaultip=192.168.60.253\0" \
-"defaultsip=192.168.60.254\0" \
+"brdefaultip=if test -r ${ipaddr}; then; else" \
+" setenv ipaddr 192.168.60.1; setenv serverip 192.168.60.254;" \
+" setenv gatewayip 192.168.60.254; setenv netmask 255.255.255.0; fi;\0" \
 "netconsole=echo switching to network console ...; " \
-"if dhcp; then " \
-"setenv ncip ${serverip}; else " \
-"setenv ncip 192.168.60.254; " \
-"setenv serverip 192.168.60.254; " \
-"setenv gatewayip 192.168.60.254; " \
-"setenv ipaddr 192.168.60.1; " \
-"fi;" \
-"setenv netdisplay0 '" \
-"setcurs 1 9; puts myip; setcurs 10 9; puts ${ipaddr};" \
-"setcurs 1 10;puts serverip; setcurs 10 10; puts ${serverip};" \
-"run netdisplay0; " \
+"if dhcp; then; else run brdefaultip; fi; setenv ncip ${serverip}; " \
+"setcurs 1 9; lcdputs myip; setcurs 10 9; lcdputs ${ipaddr};" \
+"setcurs 1 10;lcdputs serverip; setcurs 10 10; lcdputs ${serverip};" \
 "setenv stdout nc;setenv stdin nc;setenv stderr nc\0"
 
+#define CONFIG_PREBOOT                 "run brdefaultip"
 #define CONFIG_CMD_TIME
 
-#define CONFIG_SYS_GENERIC_BOARD
 
 #define CONFIG_AM33XX
 #define CONFIG_OMAP
@@ -61,7 +54,6 @@
 #define CONFIG_BAUDRATE                        115200
 
 /* Network defines */
-#define CONFIG_CMD_NET                 /* 'bootp' and 'tftp' */
 #define CONFIG_CMD_DHCP
 #define CONFIG_BOOTP_DNS               /* Configurable parts of CMD_DHCP */
 #define CONFIG_BOOTP_SEND_HOSTNAME
@@ -121,7 +113,6 @@
 #define CONFIG_CMD_I2C
 /* GPIO */
 #define CONFIG_OMAP_GPIO
-#define CONFIG_CMD_GPIO
 /*
  * ----------------------------------------------------------------------------
  * The following are general good-enough settings for U-Boot.  We set a
@@ -134,7 +125,6 @@
  */
 #define CONFIG_SYS_MALLOC_LEN          (5120 << 10)
 #define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT              "U-Boot (BuR V2.0)# "
 #define CONFIG_SYS_CONSOLE_INFO_QUIET
 #define CONFIG_ENV_OVERWRITE           /* Overwrite ethaddr / serial# */
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
@@ -156,28 +146,6 @@
                                        sizeof(CONFIG_SYS_PROMPT) + 16)
 /* Boot Argument Buffer Size */
 #define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE
-/*
- * For commands to use, we take the default list and add a few other
- * useful commands.  Note that we must have set CONFIG_SYS_NO_FLASH
- * prior to this include, in order to skip a few commands.  When we do
- * have flash, if we expect these commands they must be enabled in that
- * config.  If desired, a specific list of desired commands can be used
- * instead.
- */
-#include <config_cmd_default.h>
-/* undefine commands, which we do not need */
-#undef CONFIG_CMD_EDITENV
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_IMI
-#undef CONFIG_CMD_ITEST
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_LOADB
-#undef CONFIG_CMD_NFS
-#undef CONFIG_CMD_SETGETDCR
-#undef CONFIG_CMD_XIMG
-/* define command we need always */
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_SOURCE
 
 /*
  * Our platforms make use of SPL to initalize the hardware (primarily