*
* common parts used by B&R AM335x based boards
*
- * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> -
+ * Copyright (C) 2016 Hannes Schmelzer <oe5hpm@oevsv.at> -
* Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
*
* SPDX-License-Identifier: GPL-2.0+
#define CONFIG_AM33XX
#define CONFIG_OMAP
#define CONFIG_OMAP_COMMON
-#define CONFIG_BOARD_LATE_INIT
#define CONFIG_SYS_CACHELINE_SIZE 64
#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */
#include <asm/arch/omap.h>
/* NS16550 Configuration */
-#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
#define CONFIG_SYS_NS16550_CLK 48000000
#define CONFIG_BAUDRATE 115200
/* Network defines */
-#define CONFIG_CMD_NET /* 'bootp' and 'tftp' */
-#define CONFIG_CMD_DHCP
-#define CONFIG_BOOTP_DNS /* Configurable parts of CMD_DHCP */
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_NET_RETRY_COUNT 4
-#define CONFIG_CMD_PING
#define CONFIG_DRIVER_TI_CPSW /* Driver for IP block */
#define CONFIG_MII /* Required in net/eth.c */
-#define CONFIG_SPL_ETH_SUPPORT
#define CONFIG_PHYLIB
#define CONFIG_PHY_NATSEMI
-#define CONFIG_SPL_NET_SUPPORT
-#define CONFIG_SPL_ENV_SUPPORT /* used for a fetching MAC-Address */
-#define CONFIG_SPL_NET_VCI_STRING "AM335x U-Boot SPL"
/*
* SPL related defines. The Public RAM memory map the ROM defines the
#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
#define CONFIG_SYS_I2C_OMAP24XX
-
/* GPIO */
#define CONFIG_OMAP_GPIO
-#define CONFIG_CMD_GPIO
-/*
- * ----------------------------------------------------------------------------
- * The following are general good-enough settings for U-Boot. We set a
- * large malloc pool as we generally have a lot of DDR, and we opt for
- * function over binary size in the main portion of U-Boot as this is
- * generally easily constrained later if needed. We enable the config
- * options that give us information in the environment about what board
- * we are on so we do not need to rely on the command prompt. We set a
- * console baudrate of 115200 and use the default baud rate table.
- */
-#define CONFIG_SYS_MALLOC_LEN (1024 << 10)
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT "U-Boot (BuR V2.0)# "
-#define CONFIG_SYS_CONSOLE_INFO_QUIET
-#define CONFIG_ENV_OVERWRITE /* Overwrite ethaddr / serial# */
-
-/* As stated above, the following choices are optional. */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_VERSION_VARIABLE
-
-/* We set the max number of command args high to avoid HUSH bugs. */
-#define CONFIG_SYS_MAXARGS 64
-
-/* Console I/O Buffer Size */
-#define CONFIG_SYS_CBSIZE 512
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE +\
- sizeof(CONFIG_SYS_PROMPT) + 16)
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-/*
- * For commands to use, we take the default list and add a few other
- * useful commands. Note that we must have set CONFIG_SYS_NO_FLASH
- * prior to this include, in order to skip a few commands. When we do
- * have flash, if we expect these commands they must be enabled in that
- * config. If desired, a specific list of desired commands can be used
- * instead.
- */
-#include <config_cmd_default.h>
-/* undefine commands, which we do not need */
-#undef CONFIG_CMD_EDITENV
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_IMI
-#undef CONFIG_CMD_ITEST
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_LOADB
-#undef CONFIG_CMD_NFS
-#undef CONFIG_CMD_SETGETDCR
-#undef CONFIG_CMD_XIMG
-#undef CONFIG_CMD_CRC32
-/* define command we need always */
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_SOURCE
/*
* Our platforms make use of SPL to initalize the hardware (primarily
* under common/spl/. Given our generally common memory map, we set a
* number of related defaults and sizes here.
*/
-#define CONFIG_SPL
#define CONFIG_SPL_FRAMEWORK
/*
* Place the image at the start of the ROM defined image space.
*
* ----------------------------------------------------------------------------
*/
-#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
#undef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0x80800000
#define CONFIG_SPL_BSS_START_ADDR 0x80A00000