* Network Settings
*/
#define ADI_CMDS_NETWORK 1
-#define CONFIG_NET_MULTI
#define CONFIG_SMC91111 1
#define CONFIG_SMC91111_BASE 0x2C010300
#define CONFIG_SMC_USE_32_BIT 1
#define CONFIG_SYS_MAX_FLASH_SECT 135
/* The BF561-EZKIT uses a top boot flash */
#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR 0x20004000
-#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE)
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x10000
-#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
-#define ENV_IS_EMBEDDED
-#else
-#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
-#endif
-#ifdef ENV_IS_EMBEDDED
-/* WARNING - the following is hand-optimized to fit within
- * the sector before the environment sector. If it throws
- * an error during compilation remove an object here to get
- * it linked after the configuration sector.
- */
-# define LDS_BOARD_TEXT \
- cpu/blackfin/traps.o (.text .text.*); \
- cpu/blackfin/interrupt.o (.text .text.*); \
- cpu/blackfin/serial.o (.text .text.*); \
- common/dlmalloc.o (.text .text.*); \
- lib_generic/crc32.o (.text .text.*); \
- lib_generic/zlib.o (.text .text.*); \
- board/bf561-ezkit/bf561-ezkit.o (.text .text.*); \
- . = DEFINED(env_offset) ? env_offset : .; \
- common/env_embedded.o (.text .text.*);
-#endif
+#define CONFIG_ENV_OFFSET (0x800000 - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
+#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
+#define CONFIG_ENV_SECT_SIZE 0x2000
/*
* I2C Settings
*/
-#define CONFIG_SOFT_I2C
-#ifdef CONFIG_SOFT_I2C
-#define PF_SCL PF0
-#define PF_SDA PF1
-#define I2C_INIT \
- do { \
- *pFIO0_DIR |= PF_SCL; \
- SSYNC(); \
- } while (0)
-#define I2C_ACTIVE \
- do { \
- *pFIO0_DIR |= PF_SDA; \
- *pFIO0_INEN &= ~PF_SDA; \
- SSYNC(); \
- } while (0)
-#define I2C_TRISTATE \
- do { \
- *pFIO0_DIR &= ~PF_SDA; \
- *pFIO0_INEN |= PF_SDA; \
- SSYNC(); \
- } while (0)
-#define I2C_READ ((*pFIO0_FLAG_D & PF_SDA) != 0)
-#define I2C_SDA(bit) \
- do { \
- if (bit) \
- *pFIO0_FLAG_S = PF_SDA; \
- else \
- *pFIO0_FLAG_C = PF_SDA; \
- SSYNC(); \
- } while (0)
-#define I2C_SCL(bit) \
- do { \
- if (bit) \
- *pFIO0_FLAG_S = PF_SCL; \
- else \
- *pFIO0_FLAG_C = PF_SCL; \
- SSYNC(); \
- } while (0)
+#define CONFIG_SYS_I2C_SOFT
+#ifdef CONFIG_SYS_I2C_SOFT
+#define CONFIG_SYS_I2C
+#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF0
+#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF1
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-
-#define CONFIG_SYS_I2C_SPEED 50000
-#define CONFIG_SYS_I2C_SLAVE 0
+#define CONFIG_SYS_I2C_SOFT_SPEED 50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE 0
#endif
-
/*
* Misc Settings
*/
#define CONFIG_UART_CONSOLE 0
+/*
+ * Run core 1 from L1 SRAM start address when init uboot on core 0
+ */
+/* #define CONFIG_CORE1_RUN 1 */
+
/*
* Pull in common ADI header for remaining command/environment setup