/*
- * U-boot - Configuration file for BF533 EZKIT board
+ * U-Boot - Configuration file for BF533 EZKIT board
*/
#ifndef __CONFIG_BF533_EZKIT_H__
#include <asm/config-pre.h>
-
/*
* Processor Settings
*/
#define CONFIG_BFIN_CPU bf533-0.3
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
-
/*
* Clock Settings
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
/* Values can range from 1-15 */
#define CONFIG_SCLK_DIV 5
-
/*
* Memory Settings
*/
#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
#define CONFIG_SYS_MALLOC_LEN (128 * 1024)
-
/*
* Network Settings
*/
#define ADI_CMDS_NETWORK 1
-#define CONFIG_DRIVER_SMC91111 1
+#define CONFIG_SMC91111 1
#define CONFIG_SMC91111_BASE 0x20310300
#define SMC91111_EEPROM_INIT() \
do { \
- *pFIO_DIR |= PF1; \
- *pFIO_FLAG_S = PF1; \
+ bfin_write_FIO_DIR(bfin_read_FIO_DIR() | PF1 | PF0); \
+ bfin_write_FIO_FLAG_C(PF1); \
+ bfin_write_FIO_FLAG_S(PF0); \
SSYNC(); \
} while (0)
#define CONFIG_HOSTNAME bf533-ezkit
-/* Uncomment next line to use fixed MAC address */
-/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
-
/*
* Flash Settings
#define CONFIG_SYS_MAX_FLASH_BANKS 3
#define CONFIG_SYS_MAX_FLASH_SECT 40
#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR 0x20020000
+#define CONFIG_ENV_ADDR 0x20030000
#define CONFIG_ENV_SECT_SIZE 0x10000
#define FLASH_TOT_SECT 40
-
/*
* I2C Settings
- * By default PF1 is used as SDA and PF0 as SCL on the Stamp board
*/
-#define CONFIG_SOFT_I2C
-#ifdef CONFIG_SOFT_I2C
-#define PF_SCL PF0
-#define PF_SDA PF1
-#define I2C_INIT \
- do { \
- *pFIO_DIR |= PF_SCL; \
- SSYNC(); \
- } while (0)
-#define I2C_ACTIVE \
- do { \
- *pFIO_DIR |= PF_SDA; \
- *pFIO_INEN &= ~PF_SDA; \
- SSYNC(); \
- } while (0)
-#define I2C_TRISTATE \
- do { \
- *pFIO_DIR &= ~PF_SDA; \
- *pFIO_INEN |= PF_SDA; \
- SSYNC(); \
- } while (0)
-#define I2C_READ ((*pFIO_FLAG_D & PF_SDA) != 0)
-#define I2C_SDA(bit) \
- do { \
- if (bit) \
- *pFIO_FLAG_S = PF_SDA; \
- else \
- *pFIO_FLAG_C = PF_SDA; \
- SSYNC(); \
- } while (0)
-#define I2C_SCL(bit) \
- do { \
- if (bit) \
- *pFIO_FLAG_S = PF_SCL; \
- else \
- *pFIO_FLAG_C = PF_SCL; \
- SSYNC(); \
- } while (0)
-#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-
-#define CONFIG_SYS_I2C_SPEED 50000
-#define CONFIG_SYS_I2C_SLAVE 0
+#define CONFIG_SYS_I2C_SOFT
+#ifdef CONFIG_SYS_I2C_SOFT
+#define CONFIG_SYS_I2C
+#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF0
+#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF1
+#define CONFIG_SYS_I2C_SOFT_SPEED 50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE 0
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
#endif
-
/*
* Misc Settings
*/
#define CONFIG_RTC_BFIN
#define CONFIG_UART_CONSOLE 0
-
/*
* Pull in common ADI header for remaining command/environment setup
*/