#ifndef __CONFIG_BF527_EZKIT_H__
#define __CONFIG_BF527_EZKIT_H__
-#include <asm/blackfin-config-pre.h>
+#include <asm/config-pre.h>
/*
* (can't be used same time as ethernet)
*/
#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_NAND)
-#define CONFIG_BFIN_NFC
+# define CONFIG_BFIN_NFC
+# define CONFIG_BFIN_NFC_BOOTROM_ECC
#endif
#ifdef CONFIG_BFIN_NFC
#define CONFIG_BFIN_NFC_CTL_VAL 0x0033
#define CONFIG_DRIVER_NAND_BFIN
#define CONFIG_SYS_NAND_BASE 0 /* not actually used */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define NAND_MAX_CHIPS 1
-#define CONFIG_CMD_NAND
#endif
#define CONFIG_BFIN_MAC
#define CONFIG_RMII
#define CONFIG_NETCONSOLE 1
-#define CONFIG_NET_MULTI 1
#endif
#define CONFIG_HOSTNAME bf527-ezkit
/* Uncomment next line to use fixed MAC address */
/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
-
+#define CONFIG_LIB_RAND
/*
* Flash Settings
*/
#define CONFIG_BFIN_SPI
#define CONFIG_ENV_SPI_MAX_HZ 30000000
-#define CONFIG_SF_DEFAULT_HZ 30000000
+#define CONFIG_SF_DEFAULT_SPEED 30000000
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_STMICRO
*/
#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_OFFSET 0x4000
+#define CONFIG_ENV_OFFSET 0x10000
#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
+#elif (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_NAND)
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET 0x40000
+#define CONFIG_ENV_SIZE 0x20000
#else
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_OFFSET 0x4000
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x2000
+#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
#endif
-#define ENV_IS_EMBEDDED_CUSTOM
/*
* I2C Settings
*/
-#define CONFIG_BFIN_TWI_I2C 1
-#define CONFIG_HARD_I2C 1
-#define CONFIG_SYS_I2C_SPEED 50000
-#define CONFIG_SYS_I2C_SLAVE 0
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_ADI
/*
#define CONFIG_MUSB_TIMEOUT 100000
#endif
+/* Don't waste time transferring a logo over the UART */
+#if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART)
+/*# define CONFIG_VIDEO*/
+#endif
+
+/*
+ * Video Settings
+ */
+#ifdef CONFIG_VIDEO
+#ifdef CONFIG_BF527_EZKIT_REV_2_1
+# define CONFIG_LQ035Q1_SPI_BUS 0
+# define CONFIG_LQ035Q1_SPI_CS 7
+# define CONFIG_LQ035Q1_USE_RGB565_8_BIT_PPI
+#else
+# define CONFIG_LQ035Q1_USE_RGB888_8_BIT_PPI
+#endif
+
+#ifdef CONFIG_LQ035Q1_USE_RGB565_8_BIT_PPI
+# define EASYLOGO_HEADER <asm/bfin_logo_rgb565_230x230_lzma.h>
+#else
+# define EASYLOGO_HEADER <asm/bfin_logo_230x230_lzma.h>
+#endif
+#endif /* CONFIG_VIDEO */
/*
* Misc Settings
#define CONFIG_RTC_BFIN
#define CONFIG_UART_CONSOLE 1
-/* Don't waste time transferring a logo over the UART */
-#if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART)
-# define CONFIG_VIDEO
-#endif
-
-
/*
* Pull in common ADI header for remaining command/environment setup
*/
#include <configs/bfin_adi_common.h>
-#include <asm/blackfin-config-post.h>
-
#endif