#define PHYS_SDRAM_1 V2M_BASE
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x80000)
/*
* Initial SP before reloaction is placed at end of first DRAM bank,
*/
#define CONFIG_SYS_INIT_SP_ADDR (PHYS_SDRAM_1 + 0x80000000)
/* 12MB Malloc size */
-#define CONFIG_SYS_MALLOC_LEN (SZ_8M + SZ_4M)
/* console configuration */
#define CONFIG_SYS_NS16550_CLK 25000000
#define CONFIG_SYS_MAXARGS 64
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+/*
+ * Increase max uncompressed/gunzip size, keeping size same as EMMC linux
+ * partition.
+ */
+#define CONFIG_SYS_BOOTM_LEN 0x01800000
+
+/* Access eMMC Boot_1 and Boot_2 partitions */
+
+/* enable 64-bit PCI resources */
+
+#define CONSOLE_ARGS "console_args=console=ttyS0,115200n8\0"
+#define MAX_CPUS "max_cpus=maxcpus=8\0"
+#define OS_LOG_LEVEL "log_level=loglevel=7\0"
+#define EXTRA_ARGS "extra_args=earlycon=uart8250,mmio32,0x68A10000 " \
+ "earlyelog=" __stringify(ELOG_AP_UART_LOG_BASE) ",0x10000 " \
+ "crashkernel=512M reboot=w\0"
+
+#define PCIE_ARGS "pcie_args=pci=pcie_bus_safe pcie_ports=native vfio_pci.disable_idle_d3=1\0"
+
+#ifdef CONFIG_BCM_SF2_ETH
+#define ETH_ADDR "ethaddr=00:0A:F7:95:65:A4\0"
+#define NET_ARGS "bgmac_platform.ethaddr=${ethaddr} " \
+ "ip=${ipaddr}::${gatewayip}:${netmask}::${ethif}:off"
+#else
+#define ETH_ADDR
+#define NET_ARGS
+#endif
+
+#define RESERVED_MEM "reserved_mem=memmap=0xff000000$0x1000000\0"
+
+#define BASE_ARGS "${console_args} ${extra_args} ${pcie_args}" \
+ " ${max_cpus} ${log_level} ${reserved_mem}"
+#define SETBOOTARGS "setbootargs=setenv bootargs " BASE_ARGS " " NET_ARGS "\0"
+
+#define UPDATEME_FLASH_PARAMS "bcm_compat_level=4\0" \
+ "bcm_need_recovery_rootfs=0\0" \
+ "bcm_bl_flash_pending_rfs_imgs=0\0"
+
+#define KERNEL_LOADADDR_CFG \
+ "fit_image_loadaddr=0x90000000\0" \
+ "dtb_loadaddr=0x82000000\0"
+
+#define INITRD_ARGS "initrd_args=root=/dev/ram rw\0"
+#define INITRD_LOADADDR "initrd_loadaddr=0x92000000\0"
+#define INITRD_IMAGE "initrd_image=rootfs-lake-bcm958742t.cpio.gz\0"
+#define MMC_DEV "sd_device_number=0\0"
+#define EXEC_STATE "exec_state=normal\0"
+
+#define EXT4RD_ARGS "ext4rd_args="\
+ "root=/dev/mmcblk${sd_device_number}p${gpt_partition_entry} rw rootwait\0"
+
+#define WDT_CNTRL "wdt_enable=1\0" \
+ "wdt_timeout_sec=0\0"
+
+#define ELOG_SETUP \
+ "mbox0_addr=0x66424024\0"\
+ "elog_setup="\
+ "if logsetup -s ${mbox0_addr}; then "\
+ "else "\
+ "echo ELOG is not supported by this version of the MCU patch.;"\
+ "exit;"\
+ "fi;"\
+ "if logsetup -c ${mbox0_addr}; then "\
+ "echo ELOG is ready;"\
+ "else "\
+ "echo ELOG is supported, but is not set up.;"\
+ "echo Getting setup file from the server ${serverip}...;"\
+ "if tftp ${tftp_dir}elog_src.txt; then "\
+ "echo Setting up ELOG. Please wait...;"\
+ "if logsetup ${loadaddr} ${mbox0_addr} ${filesize}; "\
+ "then "\
+ "else "\
+ "echo [logsetup] ERROR.;"\
+ "fi;"\
+ "if logsetup -c ${mbox0_addr}; then "\
+ "echo ELOG is READY.;"\
+ "else "\
+ "echo ELOG is NOT SET UP.;"\
+ "fi;"\
+ "else "\
+ "echo ELOG setup file is not available on the server.;"\
+ "fi;"\
+ "fi \0"
+
+/* eMMC partition for FIT images */
+#define FIT_MMC_PARTITION \
+ "fit_partitions=" \
+ "uuid_disk=${uuid_gpt_disk};" \
+ "name=env,size=512K,uuid=${uuid_gpt_env};" \
+ "name=Image_rsa.img,size=24MiB,uuid=${uuid_gpt_linux};" \
+ "name=Image1_rsa.img,size=24MiB,uuid=${uuid_gpt_linux1};" \
+ "name=Image2_rsa.img,size=24MiB,uuid=${uuid_gpt_linux2};" \
+ "name=nitro,size=8MiB,uuid=${uuid_gpt_nitro};" \
+ "name=recovery,size=940MiB,uuid=${uuid_gpt_recovery};" \
+ "name=rootfs,size=-,uuid=${uuid_gpt_prootfs}\0"
+
+#define QSPI_FLASH_NITRO_PARAMS \
+ "spi_nitro_img_bin_start=0x400000\0" \
+ "spi_nitro_img_bin_mirror_start=0x580000\0" \
+ "spi_nitro_bspd_cfg_start=0x700000\0" \
+ "spi_nitro_bspd_mirror_cfg_start=0x710000\0" \
+
+#define QSPI_ACCESS_ENABLE \
+ "qspi_access_en=" \
+ "mw 0x68a403e8 1;" \
+ "mw 0x68a403ec 1;" \
+ "mw 0x68a403f0 1;" \
+ "mw 0x68a403f4 1;" \
+ "mw 0x68a403f8 1;" \
+ "mw 0x68a403fc 1 \0"
+
+#define FUNC_QSPI_PROBE \
+ "func_qspi_probe="\
+ "if run qspi_access_en; then "\
+ "else "\
+ "echo ${errstr} run qspi_access_en ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if sf probe 0; then "\
+ "else "\
+ "echo echo ${errstr} sf probe command ** FAILED **;"\
+ "exit;"\
+ "fi \0"
+
+#define NITRO_FW_IMAGES \
+ "nitro_bin=nitro.img\0" \
+ "nitro_bspd_cfg=nitro_fb_bspd_config.bin\0"
+
+#define FASTBOOT_NITRO_SETUP \
+ "nitro_fastboot_type=1\0" \
+ "nitro_fastboot_secure=1\0" \
+ "nitro_fastboot_img_buffer=0\0" \
+ "nitro_fit_img_loc=0x90000000\0"
+
+#define FASTBOOT_SETUP \
+ "fastboot_nitro_setup=" \
+ "setenv errstr fastboot_setup;" \
+ "run func_qspi_probe;" \
+ /* first load header only */ \
+ "if sf read ${nitro_fit_img_loc} "\
+ "${spi_nitro_img_bin_start} 0x18; then "\
+ "else "\
+ "echo [fastboot_nitro_setup] sf read "\
+ "${spi_nitro_img_bin_start} ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if spi_nitro_images_addr ${nitro_fit_img_loc} "\
+ "${spi_nitro_img_bin_start}; then "\
+ "else "\
+ "echo [fastboot_nitro_setup] spi_nitro_images_addr "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi \0"
+
+#define CHECK_CHIMP_HS\
+ "check_chimp_hs=chimp_hs"\
+ "\0"
+
+#define FASTBOOT_NITRO "fastboot_nitro=chimp_ld_secure\0"
+
+#define FIT_IMAGE "fit_image=Image_rsa.img\0"
+#define BOOTCMD_MMC_FIT \
+ "bootcmd_mmc_fit="\
+ "mmc dev ${sd_device_number};"\
+ "if test $exec_state = normal; then " \
+ "setenv use_rootfs rootfs;"\
+ "else " \
+ "setenv use_rootfs recovery;"\
+ "fi;" \
+ "echo used filesystem :${use_rootfs};"\
+ "gpt setenv mmc ${sd_device_number} ${use_rootfs};"\
+ "setenv bootargs_fs ${setbootargs} ${ext4rd_args}; run bootargs_fs;"\
+ "gpt setenv mmc ${sd_device_number} ${fit_image};"\
+ "mmc read ${fit_image_loadaddr} ${gpt_partition_addr} "\
+ "${gpt_partition_size};"\
+ "bootm ${fit_image_loadaddr}\0"
+
+#define BOOTCMD_MMC_FITS \
+ "bootcmd_mmc_fits="\
+ "setenv mmc_fit0 " \
+ "'setenv fit_image Image_rsa.img; run bootcmd_mmc_fit';"\
+ "setenv mmc_fit1 " \
+ "'setenv fit_image Image1_rsa.img; run bootcmd_mmc_fit';"\
+ "setenv mmc_fit2 " \
+ "'setenv fit_image Image2_rsa.img; run bootcmd_mmc_fit';"\
+ "run mmc_fit0 || run mmc_fit1 || run mmc_fit2\0"
+
+#define USBDEV "usbdev=0\0"
+#define BOOTCMD_USB\
+ "bootcmd_usb="\
+ "setenv usb_image_loadaddr 90000000;"\
+ "setenv fit_image Image_rsa.img;"\
+ "setenv bootargs_fs ${setbootargs} ${initrd_args}; run bootargs_fs;"\
+ "if usb dev ${usbdev}; && usb start; then "\
+ "echo Booting from USB...;"\
+ "fatload usb ${usbdev} ${usb_image_loadaddr} ${fit_image};"\
+ "fatload usb ${usbdev} ${initrd_loadaddr} ${initrd_image};"\
+ "bootm ${usb_image_loadaddr} ${initrd_loadaddr}:${filesize};"\
+ "fi;"\
+ "\0"
+
+#define START_PCI\
+ "start_pci=pci e "\
+ "\0"
+
+#define BNXT_LOAD\
+ "bnxt_load=bnxt 0 probe "\
+ "\0"
+
+#define BOOTCMD_PXE\
+ "bootcmd_pxe="\
+ "run check_chimp_hs && "\
+ "run start_pci && "\
+ "run bnxt_load;"\
+ "setenv ethact bnxt_eth0;"\
+ "setenv autoload no;"\
+ "setenv bootargs_fs ${setbootargs} ${initrd_args}; run bootargs_fs;"\
+ "if dhcp; then "\
+ "setenv pxefile_addr_r ${loadaddr};"\
+ "if pxe get; then "\
+ "setenv ramdisk_addr_r ${initrd_loadaddr};"\
+ "setenv kernel_addr_r ${fit_image_loadaddr};"\
+ "pxe boot; "\
+ "fi;"\
+ "fi;"\
+ "\0"
+
+#define FLASH_PENDING_RFS_IMGS \
+ "flash_pending_rfs_imgs=" \
+ "if test $bcm_bl_flash_pending_rfs_imgs = 1; then " \
+ "if test $bl_flash_pending_rfs_imgs = rootfs; then " \
+ "dhcp;" \
+ "run mmc_flash_rootfs;" \
+ "fi;" \
+ "if test $bl_flash_pending_rfs_imgs = recovery; then " \
+ "dhcp;" \
+ "run mmc_flash_recovery;" \
+ "fi;" \
+ "setenv bl_flash_pending_rfs_imgs;" \
+ "fi; \0"
+
+/* Flashing commands */
+#define TFTP_QSPI_PARAM \
+ "fip_qspi_addr=0x0\0"\
+ "fip_qspi_mirror_addr=0x200000\0"\
+ "loadaddr=0x90000000\0"\
+ "tftpblocksize=1468\0"\
+ "qspi_flash_fip=fip\0"\
+
+/* Flash fit_GPT partition to eMMC */
+#define MMC_FLASH_FIT_GPT \
+ "mmc_flash_gpt="\
+ "if mmc dev ${sd_device_number}; then "\
+ "else "\
+ "echo [mmc_flash_gpt] mmc dev ${sd_device_number} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if gpt write mmc ${sd_device_number} ${fit_partitions}; then "\
+ "else "\
+ "echo [mmc_flash_gpt] gpt write ${fit_partitions} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi \0"
+
+#define MMC_FLASH_IMAGE_RSA \
+ "mmc_flash_image_rsa="\
+ "if mmc dev ${sd_device_number}; then "\
+ "else "\
+ "echo [mmc_flash_image_rsa] mmc dev ${sd_device_number} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if gpt setenv mmc ${sd_device_number} ${fit_image}; then "\
+ "else "\
+ "echo [mmc_flash_image_rsa] gpt setenv ${fit_image} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if tftp ${loadaddr} ${tftp_dir}${fit_image}; then "\
+ "if test ${fit_image} = Image_rsa.img; then "\
+ "if setenv tftp_fit_image yes; then "\
+ "else "\
+ "echo [mmc_flash_image_rsa] "\
+ "setenv tftp_fit_image to yes"\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "fi;"\
+ "else "\
+ "if test ${fit_image} = Image_rsa.img; then "\
+ "echo [mmc_flash_image_rsa] tftp "\
+ "${tftp_dir}${fit_image} ** FAILED **;"\
+ "else "\
+ "if test ${tftp_fit_image} = yes; then "\
+ "if mmc write ${loadaddr} "\
+ "${gpt_partition_addr} "\
+ "${fileblocks}; then "\
+ "else "\
+ "echo "\
+ "[mmc_flash_image_rsa] "\
+ "mmc write "\
+ "${gpt_partition_addr} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "else "\
+ "echo [mmc_flash_image_rsa] tftp "\
+ "${tftp_dir}${fit_image} "\
+ "** FAILED **;"\
+ "fi;"\
+ "fi;"\
+ "exit;"\
+ "fi;"\
+ "if math add filesize filesize 1FF; then "\
+ "else "\
+ "echo [mmc_flash_image_rsa] math add command ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if math div fileblocks filesize 200; then "\
+ "else "\
+ "echo [mmc_flash_image_rsa] math div command ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if mmc write ${loadaddr} ${gpt_partition_addr} ${fileblocks}; then "\
+ "else "\
+ "echo [mmc_flash_image_rsa] mmc write ${gpt_partition_addr} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if setenv image_sz_blk_cnt ${fileblocks}; then "\
+ "else "\
+ "echo [mmc_flash_image_rsa] setenv image_sz_blk_cnt ** "\
+ "FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if saveenv; then "\
+ "else "\
+ "echo [mmc_flash_image_rsa] saveenv command ** FAILED **;"\
+ "exit;"\
+ "fi \0"
+
+#define MMC_FLASH_RECOVERY \
+ "mmc_flash_recovery="\
+ "if mmc dev ${sd_device_number}; then "\
+ "else "\
+ "echo [mmc_flash_recovery] mmc dev ${sd_device_number} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if gpt setenv mmc ${sd_device_number} recovery; then "\
+ "else "\
+ "echo [mmc_flash_recovery] gpt setenv recovery ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "setenv index 1;"\
+ "while tftp ${loadaddr} "\
+ "${tftp_dir}${gpt_partition_name}/chunk_00${index}; do "\
+ "if math add filesize filesize 1FF; then "\
+ "else "\
+ "echo [mmc_flash_recovery] math add command "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if math div fileblocks filesize 200; then "\
+ "else "\
+ "echo [mmc_flash_recovery] math div command "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if mmc write ${loadaddr} ${gpt_partition_addr} "\
+ "${fileblocks}; then "\
+ "else "\
+ "echo [mmc_flash_recovery] mmc write "\
+ "${gpt_partition_addr} ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if math add index index 1; then "\
+ "else "\
+ "echo [mmc_flash_recovery] math add command "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if math add gpt_partition_addr gpt_partition_addr"\
+ " ${fileblocks}; then "\
+ "else "\
+ "echo [mmc_flash_recovery] math add command"\
+ " ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "done;"\
+ "if itest ${index} -ne 1; then "\
+ "else "\
+ "echo [mmc_flash_recovery] "\
+ "${tftp_dir}${gpt_partition_name}/chunk_00${index} file "\
+ "not found ** FAILED **;"\
+ "exit;"\
+ "fi \0"
+
+#define MMC_FLASH_ROOTFS \
+ "mmc_flash_rootfs="\
+ "if mmc dev ${sd_device_number}; then "\
+ "else "\
+ "echo [mmc_flash_rootfs] mmc dev ${sd_device_number} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if gpt setenv mmc ${sd_device_number} rootfs; then "\
+ "else "\
+ "echo [mmc_flash_rootfs] gpt setenv rootfs ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "setenv index 1;"\
+ "while tftp ${loadaddr} "\
+ "${tftp_dir}${gpt_partition_name}/chunk_00${index}; do "\
+ "if math add filesize filesize 1FF; then "\
+ "else "\
+ "echo [mmc_flash_rootfs] math add command "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if math div fileblocks filesize 200; then "\
+ "else "\
+ "echo [mmc_flash_rootfs] math div command "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if mmc write ${loadaddr} ${gpt_partition_addr} "\
+ "${fileblocks}; then "\
+ "else "\
+ "echo [mmc_flash_rootfs] mmc write "\
+ "${gpt_partition_addr} ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if math add index index 1; then "\
+ "else "\
+ "echo [mmc_flash_rootfs] math add command "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if math add gpt_partition_addr gpt_partition_addr"\
+ " ${fileblocks}; then "\
+ "else "\
+ "echo [mmc_flash_rootfs] math add command"\
+ " ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "done;"\
+ "if itest ${index} -ne 1; then "\
+ "else "\
+ "echo [mmc_flash_rootfs] "\
+ "${tftp_dir}${gpt_partition_name}/chunk_00${index} file "\
+ "not found ** FAILED **;"\
+ "exit;"\
+ "fi \0"
+
+/*
+ * For individual flash commands like mmc_flash_gpt, it is not
+ * necessary to check for errors.
+ * If any of its intermediate commands fails, then next commands
+ * will not execute. Script will exit from the failure command.
+ * For uniformity, checking for mmc_flash_gpt, mmc_flash_image_rsa
+ * mmc_flash_nitro and mmc_flash_rootfs
+ */
+#define MMC_FLASH \
+ "flash_mmc="\
+ "if run mmc_flash_gpt; then "\
+ "else "\
+ "echo [flash_mmc] run mmc_flash_gpt ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if setenv tftp_fit_image no; then "\
+ "else "\
+ "echo [flash_mmc] setenv tftp_fit_image to no "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if setenv fit_image Image_rsa.img; then "\
+ "else "\
+ "echo [flash_mmc] setenv fit_image to Image_rsa.img "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if run mmc_flash_image_rsa; then "\
+ "else "\
+ "echo [flash_mmc] run mmc_flash_image_rsa ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if setenv fit_image Image1_rsa.img; then "\
+ "else "\
+ "echo [flash_mmc] setenv fit_image to Image1_rsa.img "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if run mmc_flash_image_rsa; then "\
+ "else "\
+ "echo [flash_mmc] run mmc_flash_image_rsa "\
+ "for Image1_rsa.img ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if setenv fit_image Image2_rsa.img; then "\
+ "else "\
+ "echo [flash_mmc] setenv fit_image to Image2_rsa.img "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if run mmc_flash_image_rsa; then "\
+ "else "\
+ "echo [flash_mmc] run mmc_flash_image_rsa "\
+ "for Image2_rsa.img ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if run mmc_flash_recovery; then "\
+ "else "\
+ "echo [flash_mmc] run mmc_flash_recovery ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if run mmc_flash_rootfs; then "\
+ "else "\
+ "echo [flash_mmc] run mmc_flash_rootfs ** FAILED **;"\
+ "exit;"\
+ "fi \0"
+
+#define FUNC_ALIGN_QSPI_ERASE_BLOCK_SIZE \
+ "align_erase_blk_size=" \
+ "setenv fl_write_size 0;" \
+ "if math add fl_write_size filesize FFFF; then "\
+ "else "\
+ "echo ${errstr} math add command ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if math div fl_write_size fl_write_size 10000; then "\
+ "else "\
+ "echo ${errstr} math div command ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if math mul fl_write_size fl_write_size 10000; then "\
+ "else "\
+ "echo ${errstr} math mul command ** FAILED **;"\
+ "exit;"\
+ "fi \0"
+
+#define QSPI_FLASH_FIP \
+ "flash_fip="\
+ "if run qspi_access_en; then "\
+ "else "\
+ "echo [flash_fip] run qspi_access_en ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if tftp ${loadaddr} ${tftp_dir}fip.bin; then "\
+ "else "\
+ "echo [flash_fip] tftp ${tftp_dir}fip.bin "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if math add tmpsize filesize FFFF; then "\
+ "else "\
+ "echo [flash_fip] math add command ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if math div tmpsize tmpsize 10000; then "\
+ "else "\
+ "echo [flash_fip] math div command ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if math mul tmpsize tmpsize 10000; then "\
+ "else "\
+ "echo [flash_fip] math mul command ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if sf probe 0; then "\
+ "else "\
+ "echo [flash_fip] sf probe command ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if sf erase ${fip_qspi_addr} ${tmpsize}; then "\
+ "else "\
+ "echo [flash_fip] sf erase ${fip_qspi_addr} ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if sf write ${loadaddr} ${fip_qspi_addr} ${filesize}; then "\
+ "else "\
+ "echo [flash_fip] sf write ${fip_qspi_addr} ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ /* Flash mirror FIP image */ \
+ "if sf erase ${fip_qspi_mirror_addr} ${tmpsize}; then "\
+ "else "\
+ "echo [flash_fip] sf erase ${fip_qspi_mirror_addr} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if sf write ${loadaddr} ${fip_qspi_mirror_addr} ${filesize}; then "\
+ "else "\
+ "echo [flash_fip] sf write ${fip_qspi_mirror_addr} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi \0"
+
+#define QSPI_FLASH_NITRO \
+ "flash_nitro="\
+ "run func_qspi_probe; "\
+ "if tftp ${loadaddr} ${tftp_dir}${nitro_bin}; then "\
+ "else "\
+ "echo [flash_nitro] tftp ${tftp_dir}${nitro_bin} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "setenv errstr flash_nitro;" \
+ "run align_erase_blk_size;" \
+ /* Flash Nitro fw fit + configuration */ \
+ "if sf erase ${spi_nitro_img_bin_start} ${fl_write_size}; then "\
+ "else "\
+ "echo [flash_nitro] sf erase ${spi_nitro_img_bin_start} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if sf write ${loadaddr} ${spi_nitro_img_bin_start}" \
+ " ${fl_write_size}; then "\
+ "else "\
+ "echo [flash_nitro] sf write ${spi_nitro_bin_start} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ /* Mirror of Flash Nitro fw fit + configuration */ \
+ "if sf erase ${spi_nitro_img_bin_mirror_start} ${fl_write_size}; then "\
+ "else "\
+ "echo [flash_nitro] sf erase "\
+ "${spi_nitro_img_bin_mirror_start} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if sf write ${loadaddr} ${spi_nitro_img_bin_mirror_start}" \
+ " ${fl_write_size}; then "\
+ "else "\
+ "echo [flash_nitro] sf write "\
+ "${spi_nitro_img_bin_mirror_start} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi \0"
+
+#define QSPI_FLASH_NITRO_BSPD_CONFIG \
+ "flash_nitro_bspd_config="\
+ "run func_qspi_probe; "\
+ /* Flash BSPD configuration */ \
+ "if tftp ${loadaddr} ${tftp_dir}${nitro_bspd_cfg}; then "\
+ "setenv bspd_cfg_avialable 1; "\
+ "setenv errstr flash_nitro_bspd_config; "\
+ "run align_erase_blk_size;" \
+ "if sf erase ${spi_nitro_bspd_cfg_start} "\
+ "${fl_write_size}; then "\
+ "else "\
+ "echo [flash_nitro] sf erase "\
+ "${spi_nitro_bspd_cfg_start} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if sf write ${loadaddr} ${spi_nitro_bspd_cfg_start} "\
+ "${fl_write_size}; then "\
+ "else "\
+ "echo [flash_nitro] sf write "\
+ "${spi_nitro_bspd_cfg_start} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;" \
+ /* Flash BSPD mirror configuration */ \
+ "if sf erase ${spi_nitro_bspd_mirror_cfg_start} "\
+ "${fl_write_size}; then "\
+ "else "\
+ "echo [flash_nitro] sf erase "\
+ "${spi_nitro_bspd_mirror_cfg_start} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if sf write ${loadaddr} ${spi_nitro_bspd_mirror_cfg_start} "\
+ "${fl_write_size}; then "\
+ "else "\
+ "echo [flash_nitro] sf write "\
+ "${spi_nitro_bspd_mirror_cfg_start} "\
+ "** FAILED **;"\
+ "exit;"\
+ "fi;" \
+ "else "\
+ "echo [flash_nitro] tftp ${tftp_dir}${nitro_bspd_cfg} "\
+ "** Skip flashing bspd config file **;"\
+ "fi \0"
+
+#define QSPI_FLASH \
+ "flash_qspi="\
+ "if run qspi_access_en; then "\
+ "else "\
+ "echo [flash_qspi] run qspi_access_en ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if run flash_fip; then "\
+ "else "\
+ "echo [flash_qspi] run flash_fip ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if run flash_nitro; then "\
+ "else "\
+ "echo [flash_qspi] run flash_nitro ** FAILED **;"\
+ "exit;"\
+ "fi \0"
+
+#define FLASH_IMAGES \
+ "flash_images=" \
+ "if run flash_qspi; then "\
+ "else "\
+ "echo [flash_images] run flash_qspi ** FAILED **;"\
+ "exit;"\
+ "fi;"\
+ "if run flash_mmc; then "\
+ "else "\
+ "echo [flash_images] run flash_mmc ** FAILED **;"\
+ "exit;"\
+ "fi \0"
+
+#define ARCH_ENV_SETTINGS \
+ CONSOLE_ARGS \
+ MAX_CPUS \
+ OS_LOG_LEVEL \
+ EXTRA_ARGS \
+ PCIE_ARGS \
+ ETH_ADDR \
+ RESERVED_MEM \
+ SETBOOTARGS \
+ UPDATEME_FLASH_PARAMS \
+ KERNEL_LOADADDR_CFG\
+ INITRD_ARGS \
+ INITRD_LOADADDR \
+ INITRD_IMAGE \
+ MMC_DEV \
+ EXEC_STATE \
+ EXT4RD_ARGS \
+ WDT_CNTRL \
+ ELOG_SETUP \
+ FIT_MMC_PARTITION \
+ QSPI_FLASH_NITRO_PARAMS \
+ QSPI_ACCESS_ENABLE \
+ FUNC_QSPI_PROBE \
+ NITRO_FW_IMAGES \
+ FASTBOOT_NITRO_SETUP \
+ FASTBOOT_SETUP \
+ CHECK_CHIMP_HS \
+ FASTBOOT_NITRO \
+ FIT_IMAGE \
+ BOOTCMD_MMC_FIT \
+ BOOTCMD_MMC_FITS \
+ USBDEV \
+ BOOTCMD_USB \
+ START_PCI \
+ BNXT_LOAD \
+ BOOTCMD_PXE \
+ FLASH_PENDING_RFS_IMGS \
+ TFTP_QSPI_PARAM \
+ MMC_FLASH_FIT_GPT \
+ MMC_FLASH_IMAGE_RSA \
+ MMC_FLASH_RECOVERY \
+ MMC_FLASH_ROOTFS \
+ MMC_FLASH \
+ FUNC_ALIGN_QSPI_ERASE_BLOCK_SIZE \
+ QSPI_FLASH_FIP \
+ QSPI_FLASH_NITRO \
+ QSPI_FLASH_NITRO_BSPD_CONFIG \
+ QSPI_FLASH \
+ FLASH_IMAGES
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ ARCH_ENV_SETTINGS
+
#endif /* __BCM_NS3_H */
projects / platform / kernel / u-boot.git / blobdiff