/*-----------------------------------------------------------------------
* High Level Configuration Options
*----------------------------------------------------------------------*/
-#define CONFIG_BAMBOO 1 /* Board is BAMBOO */
-#define CONFIG_440_EP 1 /* Specific PPC440EP support */
+#define CONFIG_BAMBOO 1 /* Board is BAMBOO */
+#define CONFIG_440_EP 1 /* Specific PPC440EP support */
-#define CONFIG_4xx 1 /* ... PPC4xx family */
+#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#undef CFG_DRAM_TEST /* disable - takes long time! */
-//#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CFG_FLASH_BASE 0xfe000000 /* start of FLASH */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
-#define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory */
-#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
-#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
-#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000
-
+#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
+#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
+#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
+#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
+#define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */
+#define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/
+#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
+#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
+#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000
/*Don't change either of these*/
-#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
-#define CFG_PCI_BASE 0xe0000000 /* internal PCI regs */
+#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals*/
+#define CFG_PCI_BASE 0xe0000000 /* internal PCI regs*/
/*Don't change either of these*/
-#define CFG_USB_DEVICE 0x50000000
-#define CFG_NVRAM_BASE_ADDR 0x80000000
-#define CFG_BCSR_BASE (CFG_NVRAM_BASE_ADDR | 0x2000)
+#define CFG_USB_DEVICE 0x50000000
+#define CFG_NVRAM_BASE_ADDR 0x80000000
+#define CFG_BCSR_BASE (CFG_NVRAM_BASE_ADDR | 0x2000)
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in SDRAM)
*----------------------------------------------------------------------*/
-#define CFG_INIT_RAM_ADDR 0xf0000000 /* DCache */
-#define CFG_INIT_RAM_END 0x2000
+#define CFG_INIT_RAM_ADDR 0xf0000000 /* DCache */
+#define CFG_INIT_RAM_END 0x1000
#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/
-#define CFG_KBYTES_SDRAM ( 128 * 1024) /* 128MB */
-//#define CFG_SDRAM_BANKS (2)
-#define CFG_SDRAM_BANKS (1)
-
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
#define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
-/*define this if you want console on UART1*/
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SERIAL_MULTI 1
+/* define this if you want console on UART1 */
#undef CONFIG_UART1_CONSOLE
#define CFG_BAUDRATE_TABLE \
#define CONFIG_RTC_DS1556 1 /* DS1556 RTC */
/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+/*
+ * Define here the location of the environment variables (FLASH or EEPROM).
+ * Note: DENX encourages to use redundant environment in FLASH.
+ */
+#if 1
+#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#else
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#endif
+
+/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
-#if 0 /* test-only */
-#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
+#define CFG_MAX_FLASH_BANKS 3 /* number of banks */
#define CFG_MAX_FLASH_SECT 256 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 120000 /* Timeout for Flash Write (in ms) */
-#else
-#define CFG_FLASH_CFI /* The flash is CFI compatible */
-#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CFG_FLASH_CFI_AMD_RESET 1 /* AMD RESET for STM 29W320DB! */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+#define CFG_FLASH_ADDR0 0x555
+#define CFG_FLASH_ADDR1 0x2aa
+#define CFG_FLASH_WORD_SIZE unsigned char
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CFG_FLASH_2ND_16BIT_DEV 1 /* bamboo has 8 and 16bit device */
+#define CFG_FLASH_2ND_ADDR 0x87800000 /* bamboo has 8 and 16bit device */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#ifdef CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
+#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+
+#if 0 /* test-only */
+/* Address and size of Redundant Environment Sector */
+#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
#endif
+#endif /* CFG_ENV_IS_IN_FLASH */
/*-----------------------------------------------------------------------
* DDR SDRAM
- *----------------------------------------------------------------------*/
-#undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */
+ *----------------------------------------------------------------------------- */
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
+#define SPD_EEPROM_ADDRESS {0x50,0x51} /* SPD i2c spd addresses */
+#define CFG_SDRAM_ONBOARD_SIZE (64 << 20) /* Bamboo has onboard and DIMM-slots!*/
/*-----------------------------------------------------------------------
* I2C
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-
-/*-----------------------------------------------------------------------
- * Environment
- *----------------------------------------------------------------------*/
-#undef CFG_ENV_IS_IN_NVRAM /*No NVRAM on board*/
-#undef CFG_ENV_IS_IN_FLASH /* ... not in flash */
-#define CFG_ENV_IS_IN_EEPROM 1
-
-/* Define to allow the user to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
#define CFG_I2C_MULTI_EEPROMS
-#define CFG_ENV_SIZE 0x200 /* Size of Environment vars */
-#define CFG_ENV_OFFSET 0x0
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
#define CFG_I2C_EEPROM_ADDR_LEN 1
#define CFG_EEPROM_PAGE_WRITE_ENABLE
#define CFG_EEPROM_PAGE_WRITE_BITS 3
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CONFIG_BOOTCOMMAND "bootm 0xfe000000" /* autoboot command */
-#define CONFIG_BOOTDELAY 3 /* disable autoboot */
+#ifdef CFG_ENV_IS_IN_EEPROM
+#define CFG_ENV_SIZE 0x200 /* Size of Environment vars */
+#define CFG_ENV_OFFSET 0x0
+#endif /* CFG_ENV_IS_IN_EEPROM */
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo"
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "hostname=bamboo\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$(serverip):$(rootpath)\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs $(bootargs) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
+ ":$(hostname):$(netdev):off panic=1\0" \
+ "addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\
+ "flash_nfs=run nfsargs addip addtty;" \
+ "bootm $(kernel_addr)\0" \
+ "flash_self=run ramargs addip addtty;" \
+ "bootm $(kernel_addr) $(ramdisk_addr)\0" \
+ "net_nfs=tftp 200000 $(bootfile);run nfsargs addip addtty;" \
+ "bootm\0" \
+ "rootpath=/opt/eldk/ppc_4xx\0" \
+ "bootfile=/tftpboot/bamboo/uImage\0" \
+ "kernel_addr=fff00000\0" \
+ "ramdisk_addr=fff10000\0" \
+ "load=tftp 100000 /tftpboot/bamboo/u-boot.bin\0" \
+ "update=protect off fff80000 ffffffff;era fff80000 ffffffff;" \
+ "cp.b 100000 fff80000 80000;" \
+ "setenv filesize;saveenv\0" \
+ "upd=run load;run update\0" \
+ ""
+#define CONFIG_BOOTCOMMAND "run flash_self"
+
+#if 0
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+
+#define CONFIG_BAUDRATE 115200
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_NET_MULTI 1 /* required for netconsole */
-#define CONFIG_PHY1_ADDR 3
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_NET_MULTI 1 /* required for netconsole */
+#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
+#define CONFIG_PHY1_ADDR 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
-#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_IPADDR 10.0.4.251
-#define CONFIG_ETHADDR 00:10:EC:00:12:34
-#define CONFIG_ETH1ADDR 00:10:EC:00:12:35
+#define CONFIG_NO_PHY_RESET 1 /* no PHY reset on bamboo!!! */
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-#define CONFIG_SERVERIP 10.0.4.115
+#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
/* Partitions */
#define CONFIG_MAC_PARTITION
#define USB_2_0_DEVICE
#endif /*CONFIG_440_EP*/
-#ifdef DEBUG
-#define CONFIG_PANIC_HANG
-#else
-#define CONFIG_HW_WATCHDOG /* watchdog */
-#endif
-
-#ifdef CONFIG_440_EP
- /* Need to define POST */
-#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_DIAG | \
- CFG_CMD_ECHO | \
- CFG_CMD_EEPROM | \
- CFG_CMD_ELF | \
- /* CFG_CMD_EXT2 |*/ \
- /* CFG_CMD_FAT |*/ \
- CFG_CMD_I2C | \
- /* CFG_CMD_IDE |*/ \
- CFG_CMD_IRQ | \
- /* CFG_CMD_KGDB |*/ \
- CFG_CMD_MII | \
- CFG_CMD_PCI | \
- CFG_CMD_PING | \
- CFG_CMD_REGINFO | \
- CFG_CMD_SDRAM | \
- CFG_CMD_FLASH | \
- /* CFG_CMD_SPI |*/ \
- CFG_CMD_USB | \
- 0 ) & ~CFG_CMD_IMLS)
-#else
-#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_DIAG | \
- CFG_CMD_ECHO | \
- CFG_CMD_EEPROM | \
- CFG_CMD_ELF | \
- /* CFG_CMD_EXT2 |*/ \
- /* CFG_CMD_FAT |*/ \
- CFG_CMD_I2C | \
- /* CFG_CMD_IDE |*/ \
- CFG_CMD_IRQ | \
- /* CFG_CMD_KGDB |*/ \
- CFG_CMD_MII | \
- CFG_CMD_PCI | \
- CFG_CMD_PING | \
- CFG_CMD_REGINFO | \
- CFG_CMD_SDRAM | \
- CFG_CMD_FLASH | \
- /* CFG_CMD_SPI |*/ \
- 0 ) & ~CFG_CMD_IMLS)
-#endif
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CFG_CMD_ASKENV | \
+ CFG_CMD_DATE | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_DIAG | \
+ CFG_CMD_ELF | \
+ CFG_CMD_I2C | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_MII | \
+ CFG_CMD_NET | \
+ CFG_CMD_NFS | \
+ CFG_CMD_PCI | \
+ CFG_CMD_PING | \
+ CFG_CMD_REGINFO | \
+ CFG_CMD_SDRAM | \
+ CFG_CMD_USB | \
+ CFG_CMD_SNTP )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_DCACHE_SIZE 8192 /* For IBM 405 CPUs */
+#define CFG_DCACHE_SIZE 32768 /* For IBM 440 CPUs */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
projects / platform / kernel / u-boot.git / blobdiff