#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_DISPLAY_CPUINFO
/* general purpose I/O */
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
-#define CONFIG_AT91_GPIO
-#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */
-
-/* serial console */
-#define CONFIG_ATMEL_USART
-#define CONFIG_USART_BASE ATMEL_BASE_DBGU
-#define CONFIG_USART_ID ATMEL_ID_SYS
/* LCD */
-#define CONFIG_LCD
#define LCD_BPP LCD_COLOR8
#define CONFIG_LCD_LOGO
#undef LCD_TEST_PATTERN
#define CONFIG_LCD_INFO
#define CONFIG_LCD_INFO_BELOW_LOGO
-#define CONFIG_SYS_WHITE_ON_BLACK
#define CONFIG_ATMEL_LCD
#define CONFIG_ATMEL_LCD_RGB565
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
/* board specific(not enough SRAM) */
#define CONFIG_AT91SAM9G45_LCD_BASE 0x73E00000
-/* LED */
-#define CONFIG_AT91_LED
-#define CONFIG_RED_LED AT91_PIN_PD31 /* this is the user1 led */
-#define CONFIG_GREEN_LED AT91_PIN_PD0 /* this is the user2 led */
-
-
/*
* BOOTP options
*/
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
-/*
- * Command line configuration.
- */
-
-/* No NOR flash */
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_CMD_NAND
-
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS6
#define CONFIG_SYS_SDRAM_SIZE 0x08000000
#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
+ (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
/* NAND flash */
#ifdef CONFIG_CMD_NAND
#endif
-/* MMC */
-
-#ifdef CONFIG_CMD_MMC
-#define CONFIG_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_GENERIC_ATMEL_MCI
-#endif
-
-#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
-#define CONFIG_DOS_PARTITION
-#endif
-
/* Ethernet */
-#define CONFIG_MACB
-#define CONFIG_RMII
-#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_RESET_PHY_R
#define CONFIG_AT91_WANTS_COMMON_PHY
-/* USB */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_ATMEL
-#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
-
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#ifdef CONFIG_SYS_USE_NANDFLASH
/* bootstrap + u-boot + env in nandflash */
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_OFFSET 0xc0000
+#define CONFIG_ENV_OFFSET 0x120000
#define CONFIG_ENV_OFFSET_REDUND 0x100000
#define CONFIG_ENV_SIZE 0x20000
"root=/dev/mtdblock7 rw rootfstype=jffs2"
#elif CONFIG_SYS_USE_MMC
/* bootstrap + u-boot + env + linux in mmc */
-#define FAT_ENV_INTERFACE "mmc"
-/*
- * We don't specify the part number, if device 0 has partition table, it means
- * the first partition; it no partition table, then take whole device as a
- * FAT file system.
- */
-#define FAT_ENV_DEVICE_AND_PART "0"
-#define FAT_ENV_FILE "uboot.env"
-#define CONFIG_ENV_IS_IN_FAT
-#define CONFIG_FAT_WRITE
#define CONFIG_ENV_SIZE 0x4000
#define CONFIG_BOOTARGS "console=ttyS0,115200 " \
"bootz 0x72000000 - 0x71000000"
#endif
-#define CONFIG_BAUDRATE 115200
-
#define CONFIG_SYS_CBSIZE 256
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00080000
#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"