Convert CONFIG_SYS_FLASH_ERASE_TOUT et al to Kconfig

[platform/kernel/u-boot.git] / include / configs / astro_mcf5373l.h

diff --git a/include/configs/astro_mcf5373l.h b/include/configs/astro_mcf5373l.h
index 65c7d03..f851084 100644 (file)
--- a/include/configs/astro_mcf5373l.h
+++ b/include/configs/astro_mcf5373l.h
@@ -51,14 +51,7 @@
 #define ENABLE_JFFS    1
 #endif
 
-#define CONFIG_MCFRTC
-#undef RTC_DEBUG
-
-/* Timer */
-#define CONFIG_MCFTMR
-
 /* I2C */
-#define CONFIG_SYS_IMMR                        CONFIG_SYS_MBAR
 
 /*
  * Defines processor clock - important for correct timings concerning serial
@@ -72,8 +65,6 @@
 #define CONFIG_SYS_CORE_SRAM_SIZE      0x8000
 #define CONFIG_SYS_CORE_SRAM           0x80000000
 
-#define CONFIG_SYS_UNIFY_CACHE
-
 /*
  * Define baudrate for UART1 (console output, tftp, ...)
  * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud
@@ -81,7 +72,6 @@
  * in u-boot command interface
  */
 
-#define CONFIG_MCFUART
 #define CONFIG_SYS_UART_PORT           (2)
 #define CONFIG_SYS_UART2_ALT3_GPIO
 
@@ -92,7 +82,6 @@
  */
 
 #ifndef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_WATCHDOG
 #define CONFIG_WATCHDOG_TIMEOUT 3355   /* timeout in milliseconds */
 #endif
 
@@ -141,24 +130,7 @@
  * by external update.c; This is not included in mainline because
  * it needs non-blocking CFI routines.
  */
-#ifdef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_BOOTCOMMAND     ""      /* no autoboot in this case */
-#else
-#if ASTRO_V532
-#define CONFIG_BOOTCOMMAND     "protect off 0x80000 0x1ffffff;run env_check;"\
-                               "run xilinxload&&run alteraload&&bootm 0x80000;"\
-                               "update;reset"
-#else
-#define CONFIG_BOOTCOMMAND     "protect off 0x80000 0x1ffffff;run env_check;"\
-                               "run xilinxload&&bootm 0x80000;update;reset"
-#endif
-#endif
-
-/* default RAM address for user programs */
-#define CONFIG_SYS_LOAD_ADDR   0x20000
 
-#define CONFIG_FPGA_COUNT      1
-#define CONFIG_SYS_FPGA_PROG_FEEDBACK
 #define CONFIG_SYS_FPGA_WAIT           1000
 
 /* End of user parameters to be customized */
@@ -186,9 +158,6 @@
 #define CONFIG_SYS_INIT_RAM_ADDR       0x80000000
 #define CONFIG_SYS_INIT_RAM_SIZE               0x8000
 #define CONFIG_SYS_INIT_RAM_CTRL       0x221
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - \
-                                        GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
 /*
  * Start addresses for the final memory configuration
@@ -225,19 +194,9 @@
 
 #define CONFIG_SYS_FLASH_BASE          0x00000000
 
-#ifdef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_TEXT_BASE
-#else
-/* This is mainly used during relocation in start.S */
-#define CONFIG_SYS_MONITOR_BASE                (CONFIG_SYS_FLASH_BASE + 0x400)
-#endif
 /* Reserve 256 kB for Monitor */
 #define CONFIG_SYS_MONITOR_LEN         (256 << 10)
 
-#define CONFIG_SYS_BOOTPARAMS_LEN      (64 * 1024)
-/* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_MALLOC_LEN          (128 << 10)
-
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
@@ -247,9 +206,7 @@
                                                (CONFIG_SYS_SDRAM_SIZE << 20))
 
 /* FLASH organization */
-#define CONFIG_SYS_MAX_FLASH_BANKS     1
 #define CONFIG_SYS_MAX_FLASH_SECT      259
-#define CONFIG_SYS_FLASH_ERASE_TOUT    1000
 
 #define CONFIG_SYS_FLASH_SIZE          0x2000000
 #define CONFIG_SYS_FLASH_CFI_NONBLOCK  1
@@ -267,7 +224,6 @@
 #endif
 
 /* Cache Configuration */
-#define CONFIG_SYS_CACHELINE_SIZE      16
 
 #define ICACHE_STATUS                  (CONFIG_SYS_INIT_RAM_ADDR + \
                                         CONFIG_SYS_INIT_RAM_SIZE - 8)