*
* (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
*
- * SPDX-License-Identifier: GPL-2.0+
+ * SPDX-License-Identifier: GPL-2.0+
*/
/*
#error No card type defined!
#endif
-/*
- * Define processor
- * possible values for Urmel board: only Coldfire M5373 processor supported
- * (please do not change)
- */
-
-/* it seems not clear yet which processor defines we should use */
-#define CONFIG_MCF537x /* define processor family */
-#define CONFIG_MCF532x /* define processor family */
-#define CONFIG_M5373 /* define processor type */
#define CONFIG_ASTRO5373L /* define board type */
/* Command line configuration */
-#include <config_cmd_default.h>
-
/*
* CONFIG_RAM defines if u-boot is loaded via BDM (or started from
* a different bootloader that has already performed RAM setup) or
#define ENABLE_JFFS 1
#endif
-/* Define which commmands should be available at u-boot command prompt */
-
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_MISC
-#define CONFIG_CMD_XIMG
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_NFS
-#if ENABLE_JFFS
-#define CONFIG_CMD_JFFS2
-#endif
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_LOADS
-#define CONFIG_CMD_LOADB
-#define CONFIG_CMD_FPGA
#define CONFIG_CMDLINE_EDITING
-#define CONFIG_SYS_HUSH_PARSER
-
#define CONFIG_MCFRTC
#undef RTC_DEBUG
/*
* Defines processor clock - important for correct timings concerning serial
* interface etc.
- * CONFIG_SYS_HZ gives unit: 1000 -> 1 Hz ^= 1000 ms
*/
-#define CONFIG_SYS_HZ 1000
#define CONFIG_SYS_CLK 80000000
#define CONFIG_SYS_CPU_CLK (CONFIG_SYS_CLK * 3)
#define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */
* in u-boot command interface
*/
-#define CONFIG_BAUDRATE 115200
-
#define CONFIG_MCFUART
#define CONFIG_SYS_UART_PORT (2)
#define CONFIG_SYS_UART2_ALT3_GPIO
/* AUTOBOOT settings - booting images automatically by u-boot after power on */
/*
- * used for autoboot, delay in seconds u-boot will wait before starting
- * defined (auto-)boot command, setting to -1 disables delay, setting to
- * 0 will too prevent access to u-boot command interface: u-boot then has
- * to be reflashed
- * beware - watchdog is not serviced during autoboot delay time!
- */
-#ifdef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_BOOTDELAY 1
-#else
-#define CONFIG_BOOTDELAY 1
-#endif
-
-/*
* The following settings will be contained in the environment block ; if you
* want to use a neutral environment all those settings can be manually set in
* u-boot: 'set' command
#define CONFIG_BOOTARGS " console=ttyS2,115200 rootfstype=romfs"\
" loaderversion=$loaderversion"
-#define CONFIG_SYS_PROMPT "URMEL > "
-
/* default RAM address for user programs */
#define CONFIG_SYS_LOAD_ADDR 0x20000
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
#define CONFIG_SYS_FLASH_CFI_NONBLOCK 1
+#define LDS_BOARD_TEXT \
+ . = DEFINED(env_offset) ? env_offset : .; \
+ common/env_embedded.o (.text*)
+
#if ENABLE_JFFS
/* JFFS Partition offset set */
#define CONFIG_SYS_JFFS2_FIRST_BANK 0