common: Move CONFIG_BOOTARGS to Kconfig

[platform/kernel/u-boot.git] / include / configs / astro_mcf5373l.h

diff --git a/include/configs/astro_mcf5373l.h b/include/configs/astro_mcf5373l.h
index 828bc60..af03b30 100644 (file)
--- a/include/configs/astro_mcf5373l.h
+++ b/include/configs/astro_mcf5373l.h
@@ -57,20 +57,8 @@
 #define ENABLE_JFFS    1
 #endif
 
-/* Define which commands should be available at u-boot command prompt */
-
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_I2C
-#if ENABLE_JFFS
-#define CONFIG_CMD_JFFS2
-#endif
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_FPGA_LOADMK
 #define CONFIG_CMDLINE_EDITING
 
-#define CONFIG_SYS_HUSH_PARSER
-
 #define CONFIG_MCFRTC
 #undef RTC_DEBUG
 
@@ -107,8 +95,6 @@
  * in u-boot command interface
  */
 
-#define CONFIG_BAUDRATE                115200
-
 #define CONFIG_MCFUART
 #define CONFIG_SYS_UART_PORT           (2)
 #define CONFIG_SYS_UART2_ALT3_GPIO
@@ -132,7 +118,6 @@
 #ifndef CONFIG_MONITOR_IS_IN_RAM
 #define CONFIG_ENV_OFFSET              0x1FF8000
 #define CONFIG_ENV_SECT_SIZE           0x8000
-#define CONFIG_ENV_IS_IN_FLASH         1
 #else
 /*
  * environment in RAM - This is used to use a single PC-based application
@@ -142,7 +127,6 @@
  */
 #define CONFIG_ENV_ADDR                0x40060000
 #define CONFIG_ENV_SECT_SIZE   0x8000
-#define CONFIG_ENV_IS_IN_FLASH 1
 #endif
 
 /* here we put our FPGA configuration... */
@@ -153,19 +137,6 @@
 /* AUTOBOOT settings - booting images automatically by u-boot after power on */
 
 /*
- * used for autoboot, delay in seconds u-boot will wait before starting
- * defined (auto-)boot command, setting to -1 disables delay, setting to
- * 0 will too prevent access to u-boot command interface: u-boot then has
- * to be reflashed
- * beware - watchdog is not serviced during autoboot delay time!
- */
-#ifdef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_BOOTDELAY       1
-#else
-#define CONFIG_BOOTDELAY       1
-#endif
-
-/*
  * The following settings will be contained in the environment block ; if you
  * want to use a neutral environment all those settings can be manually set in
  * u-boot: 'set' command
@@ -202,10 +173,6 @@
 #endif
 #endif
 
-/* default bootargs that are considered during boot */
-#define CONFIG_BOOTARGS                " console=ttyS2,115200 rootfstype=romfs"\
-                               " loaderversion=$loaderversion"
-
 /* default RAM address for user programs */
 #define CONFIG_SYS_LOAD_ADDR   0x20000
 
@@ -221,10 +188,8 @@
 #define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE
 
 #define CONFIG_FPGA_COUNT      1
-#define CONFIG_FPGA
 #define        CONFIG_FPGA_XILINX
 #define        CONFIG_FPGA_SPARTAN3
-#define CONFIG_FPGA_ALTERA
 #define CONFIG_FPGA_CYCLON2
 #define CONFIG_SYS_FPGA_PROG_FEEDBACK
 #define CONFIG_SYS_FPGA_WAIT           1000