+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Configuration settings for the Sentec Cobra Board.
*
* (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
/*
* set the card type to actually compile for; either of
* the possibilities listed below has to be used!
*/
-#define CONFIG_ASTRO_V532 1
+#define ASTRO_V532 1
-#if CONFIG_ASTRO_V532
+#if ASTRO_V532
#define ASTRO_ID 0xF8
-#elif CONFIG_ASTRO_V512
+#elif ASTRO_V512
#define ASTRO_ID 0xFA
-#elif CONFIG_ASTRO_TWIN7S2
+#elif ASTRO_TWIN7S2
#define ASTRO_ID 0xF9
-#elif CONFIG_ASTRO_V912
+#elif ASTRO_V912
#define ASTRO_ID 0xFC
-#elif CONFIG_ASTRO_COFDMDUOS2
+#elif ASTRO_COFDMDUOS2
#define ASTRO_ID 0xFB
#else
#error No card type defined!
#endif
-#define CONFIG_ASTRO5373L /* define board type */
-
-/* Command line configuration */
/*
* CONFIG_RAM defines if u-boot is loaded via BDM (or started from
* a different bootloader that has already performed RAM setup) or
*/
#ifdef CONFIG_RAM
#define CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_SYS_TEXT_BASE 0x40020000
#define ENABLE_JFFS 0
#else
-#define CONFIG_SYS_TEXT_BASE 0x00000000
#define ENABLE_JFFS 1
#endif
-/* Define which commands should be available at u-boot command prompt */
-
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DATE
-#if ENABLE_JFFS
-#define CONFIG_CMD_JFFS2
-#endif
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_FPGA_LOADMK
-#define CONFIG_CMDLINE_EDITING
-
-
#define CONFIG_MCFRTC
#undef RTC_DEBUG
/* Timer */
#define CONFIG_MCFTMR
-#undef CONFIG_MCFPIT
/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 80000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
/*
* in u-boot command interface
*/
-#define CONFIG_BAUDRATE 115200
-
#define CONFIG_MCFUART
#define CONFIG_SYS_UART_PORT (2)
#define CONFIG_SYS_UART2_ALT3_GPIO
*/
#ifndef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_ENV_OFFSET 0x1FF8000
-#define CONFIG_ENV_SECT_SIZE 0x8000
-#define CONFIG_ENV_IS_IN_FLASH 1
#else
/*
* environment in RAM - This is used to use a single PC-based application
* to execute the commands from the environment. Feedback is done via setting
* and reading memory locations.
*/
-#define CONFIG_ENV_ADDR 0x40060000
-#define CONFIG_ENV_SECT_SIZE 0x8000
-#define CONFIG_ENV_IS_IN_FLASH 1
#endif
/* here we put our FPGA configuration... */
-#define CONFIG_MISC_INIT_R 1
/* Define user parameters that have to be customized most likely */
/* AUTOBOOT settings - booting images automatically by u-boot after power on */
/*
- * used for autoboot, delay in seconds u-boot will wait before starting
- * defined (auto-)boot command, setting to -1 disables delay, setting to
- * 0 will too prevent access to u-boot command interface: u-boot then has
- * to be reflashed
- * beware - watchdog is not serviced during autoboot delay time!
- */
-#ifdef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_BOOTDELAY 1
-#else
-#define CONFIG_BOOTDELAY 1
-#endif
-
-/*
* The following settings will be contained in the environment block ; if you
* want to use a neutral environment all those settings can be manually set in
* u-boot: 'set' command
#ifdef CONFIG_MONITOR_IS_IN_RAM
#define CONFIG_BOOTCOMMAND "" /* no autoboot in this case */
#else
-#if CONFIG_ASTRO_V532
+#if ASTRO_V532
#define CONFIG_BOOTCOMMAND "protect off 0x80000 0x1ffffff;run env_check;"\
"run xilinxload&&run alteraload&&bootm 0x80000;"\
"update;reset"
#endif
#endif
-/* default bootargs that are considered during boot */
-#define CONFIG_BOOTARGS " console=ttyS2,115200 rootfstype=romfs"\
- " loaderversion=$loaderversion"
-
-/* default RAM address for user programs */
-#define CONFIG_SYS_LOAD_ADDR 0x20000
-
-#define CONFIG_SYS_LONGHELP
-
-#if (CONFIG_COMMANDS & CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024
-#else
-#define CONFIG_SYS_CBSIZE 256
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
#define CONFIG_FPGA_COUNT 1
-#define CONFIG_FPGA
-#define CONFIG_FPGA_XILINX
-#define CONFIG_FPGA_SPARTAN3
-#define CONFIG_FPGA_ALTERA
-#define CONFIG_FPGA_CYCLON2
#define CONFIG_SYS_FPGA_PROG_FEEDBACK
#define CONFIG_SYS_FPGA_WAIT 1000
/* Defines memory range for test */
-#define CONFIG_SYS_MEMTEST_START 0x40020000
-#define CONFIG_SYS_MEMTEST_END 0x41ffffff
-
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
#define CONFIG_SYS_MAX_FLASH_SECT 259
#define CONFIG_SYS_FLASH_ERASE_TOUT 1000
-#define CONFIG_SYS_FLASH_CFI 1
-#define CONFIG_FLASH_CFI_DRIVER 1
#define CONFIG_SYS_FLASH_SIZE 0x2000000
-#define CONFIG_SYS_FLASH_PROTECTION 1
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
#define CONFIG_SYS_FLASH_CFI_NONBLOCK 1
#define LDS_BOARD_TEXT \
. = DEFINED(env_offset) ? env_offset : .; \
- common/env_embedded.o (.text*)
+ env/embedded.o(.text*)
#if ENABLE_JFFS
/* JFFS Partition offset set */
#endif
/* Cache Configuration */
-#define CONFIG_SYS_CACHELINE_SIZE 16
#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - 8)
projects / platform / kernel / u-boot.git / blobdiff