* set the card type to actually compile for; either of
* the possibilities listed below has to be used!
*/
-#define CONFIG_ASTRO_V532 1
+#define ASTRO_V532 1
-#if CONFIG_ASTRO_V532
+#if ASTRO_V532
#define ASTRO_ID 0xF8
-#elif CONFIG_ASTRO_V512
+#elif ASTRO_V512
#define ASTRO_ID 0xFA
-#elif CONFIG_ASTRO_TWIN7S2
+#elif ASTRO_TWIN7S2
#define ASTRO_ID 0xF9
-#elif CONFIG_ASTRO_V912
+#elif ASTRO_V912
#define ASTRO_ID 0xFC
-#elif CONFIG_ASTRO_COFDMDUOS2
+#elif ASTRO_COFDMDUOS2
#define ASTRO_ID 0xFB
#else
#error No card type defined!
#endif
-/* Command line configuration */
/*
* CONFIG_RAM defines if u-boot is loaded via BDM (or started from
* a different bootloader that has already performed RAM setup) or
/* Timer */
#define CONFIG_MCFTMR
-#undef CONFIG_MCFPIT
/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 80000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000
-#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
/*
* Defines processor clock - important for correct timings concerning serial
* in u-boot command interface
*/
-#define CONFIG_MCFUART
#define CONFIG_SYS_UART_PORT (2)
#define CONFIG_SYS_UART2_ALT3_GPIO
*/
#ifndef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_WATCHDOG
#define CONFIG_WATCHDOG_TIMEOUT 3355 /* timeout in milliseconds */
#endif
* by external update.c; This is not included in mainline because
* it needs non-blocking CFI routines.
*/
-#ifdef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_BOOTCOMMAND "" /* no autoboot in this case */
-#else
-#if CONFIG_ASTRO_V532
-#define CONFIG_BOOTCOMMAND "protect off 0x80000 0x1ffffff;run env_check;"\
- "run xilinxload&&run alteraload&&bootm 0x80000;"\
- "update;reset"
-#else
-#define CONFIG_BOOTCOMMAND "protect off 0x80000 0x1ffffff;run env_check;"\
- "run xilinxload&&bootm 0x80000;update;reset"
-#endif
-#endif
-
-/* default RAM address for user programs */
-#define CONFIG_SYS_LOAD_ADDR 0x20000
#define CONFIG_FPGA_COUNT 1
#define CONFIG_SYS_FPGA_PROG_FEEDBACK
/* Defines memory range for test */
-#define CONFIG_SYS_MEMTEST_START 0x40020000
-#define CONFIG_SYS_MEMTEST_END 0x41ffffff
-
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
#define CONFIG_SYS_MONITOR_LEN (256 << 10)
#define CONFIG_SYS_BOOTPARAMS_LEN (64 * 1024)
-/* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10)
/*
* For booting Linux, the board info and command line data
(CONFIG_SYS_SDRAM_SIZE << 20))
/* FLASH organization */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 259
#define CONFIG_SYS_FLASH_ERASE_TOUT 1000
#endif
/* Cache Configuration */
-#define CONFIG_SYS_CACHELINE_SIZE 16
#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - 8)